News Room
You are here: Home » News Room » PRODUCTS NEWS

PRODUCTS NEWS

  • Tablet press die ordering problems to pay attention to In order to make the drug factory users can better order the appropriate die, this paper makes some simple introduction, and it is suggested that the drug factory users can first have a full discussion with the die manufacturer, in order to reduce the problems that may arise during production. 1. Due to some characteristics of track design and processing technology, it is suggested that users must choose products from the same factory for tablet press and die. Do not blindly pursue cheap and buy inferior die, resulting in the damage of the tablet press. 2. Choice of tablet type: Correct choice of tablet type is a successful step for the tablet press. For example, chewable tablets have high requirements for hardness and can be easily chewed. Most of them are inclined flat tablets. Shallow concave for thin film coating. Because there is no adhesive and lubricant in the raw material of traditional Chinese medicine tablets, it is re

    2021.02.27

    Read More
  • Lubrication and maintenance of tablet press (1) all moving parts on the surface of the friction lubrication is to ensure that the machine run properly and prolong the service life of the important link, especially if the main moving parts under the condition of lack of oil dry transit transfer quickly damage and cannot be used, so the tablet machine before use must be full cup of oil, oil hole, and the friction surface and lubricating oil, and empty operation make the friction surface is full of oil film, and then can be put into use. From now on each shift refueling on time, but each refueling should not be too much, so as not to spill affect cleaning, stained tablets. (2) Each shift must check whether the screws are loose, in the process of work should also pay attention to check, if there is loose tighten immediately, so as to avoid failure. The main parts are: the upper punch fastening nut, the middle die fixing screw, the lower punch fixing screw; Connecting rod locking nut,

    2021.02.26

    Read More
  • The die composition of the tablet press The punching die is composed of the upper and lower punch and the middle die. The punch and the die hole have good coordination. The end shape of the punch can be flat, shallow concave or deep concave, and can also be engraved on the end face with words, numbers, letters, lines, etc., to indicate the name, specifications, trademarks, etc. The line is easy to take in two or three parts. The punch and die hole section shape can be round, can also be triangular, oblong and other irregular shapes. But the size of the section is limited by the pressing side, should not exceed the allowable area of the machine, so as not to increase the pressure too much, damage the machine. The tail of the punch is a groove, which is embedded in the convex part of the guide rail or the guide rail groove when working, and makes regular up and down movement. There is a groove ring in the middle of the outer circle of the middle die, which is tightened by the

    2021.02.25

    Read More
  • The use of vacuum pump for blister packing machine Start: the vacuum pump can be started after the oil level is determined. The vacuum pump must be rotated backward after the first starting and each wiring change. Operation: before normal work, the inlet pipe valve should be closed to make the pump operate for more than 15 minutes under the limit pressure state, so that the water vapor in the gas can be effectively extracted. The motor should not be started frequently (less than 6 times/hour). (Note: When the pump is running normally, the surface temperature of the oil separator, pump body and pump cover will exceed 70℃. Do not touch with your hands. The pump cannot be refueled while it is running. Limiting pressure measurement; The ultimate pressure should be measured directly at the suction port of the pump with a compression vacuum gauge. Pump once used, long term use after use, new oil should be closed after at least 1 hour of operation, so that the pump to reach the worki

    2021.02.24

    Read More
  • Pay attention to the work of the tablet press 1. Before the use of the die must be strictly checked, there can be no cracks, missing edges and hair and other phenomena, such as forced use, it will bring damage to the machine. 2. The life of the die is generally produced one million times as the design basis. When overuse, the damage rate will be greatly increased, such as rupture will damage the feeder or other parts of the accident. 3. The feeder and the turntable table must maintain a certain gap, that is, 0. 05 1. 1 mm, the gap is too large to cause the leakage of powder, too small will make the feeder and the turntable table friction, resulting in metal powder mixed into the powder, so that the pressure out of the tablet does not meet the quality requirements, become scrap. 4. Not dry and high sugar content of the particles should not be pressed, so as not to produce sticky punch, resulting in the machine can not be normal production. 5. If the automatic stop alarm is found,

    2021.02.22

    Read More
  • The process of blister packing machine 1. Before starting, manual transfer should be free of jamming phenomenon. 2. Switch on the power supply with the key and set the temperature of the two temperature control meters as required. Blowing temperature: 140--160℃ Heat sealing temperature: 190--210℃ 3. Connect 380 volt power supply. After starting the machine, the bubble blowing roller should turn clockwise. 4. Install PVC sheets and aluminum foil on their respective supporting shafts. 5. When the two meters reach the set temperature, the following operation can be performed. First, the PVC sheet passes through the small guide roller, the inner heating roller passes through the bubble suction roller and the smooth roller, and then the PVC head is pulled by hand. After starting the machine, the PVC bubble forming is more than 3 meters long, and then the hard sheet is put through the platform, the bubble blowing roller, the traveling roller and the feed roller into the

    2021.02.04

    Read More
  • The die pressure of the tablet press The pressure of the die is directly related to the material, of course, the use of hard, wear-resistant materials can significantly increase the pressure of the die can withstand, the pharmaceutical industry (global) is more common S-7, of course, the cost is relatively high, in addition to expensive raw materials, processing costs are also high; The price of several other domestic materials is low, and the domestic suppliers are more commercial, which is the reason why the domestic punching die can be sold at a lower price. The pressure that the die can bear is proportional to the area of the punch cross section, which is easier to understand; The great pressure that the die can bear is not based on experience, but needs to be measured and calculated. This result is usually included in the factory test certificate or instruction manual by the supplier; Also want to explain, is able to withstand the pressure and you don't die tablet press s

    2021.02.04

    Read More
  • Adjustment of the CAM of bubble cap machine Valve CAM on the shaft of the installation sequence: from inside to outside in turn for traction clamping cylinder CAM, cylinder CAM stop, molding blow CAM and molding cylinder CAM. When the return position of the heat sealing CAM linkage in the heat sealing die is very low, the valve CAM shall be installed according to its position. Traction machinery in the CAM traction clamping cylinder control valve slightly earlier than the CAM opened. When traction machinery traction is static, the return of the stop cylinder is clamped. After the molding mold and the blowing mold are closed, the blowing CAM opens the machine control valve, that is, blowing molding. Forming cylinder rise should be synchronized with the heat sealing CAM. Clamp of the general process is: traction after plastic sheet, plastic piece positioning cylinder to loosen, immediately manipulator to traction, manipulator in place after the stop, plastic piece posit

    2021.02.03

    Read More
  • Tablet press has a variety of technologies New tablet press and tablet technology emerge one after another. 1. Increasing pre-pressure and improving tablet quality are common considerations of many tablet press manufacturers when they launch new products. At the same time, the main pressure and pre-pressure are the same, which brings great convenience to assembly adjustment, manufacturing and product type. 2. In order to improve the utilization rate of the equipment, reduce the cost of the equipment, and make the cleaning of the equipment more standardized, the concept of WIP in-place cleaning has been implemented in more tablet presses. Foreign advanced tablet press manufacturers also pay great attention to the research of the top output, many specifications and models of the tablet press has been added in the control system of the top output display. Although China's tablet press and tablet technology has developed rapidly and made great achievements, compared with develo

    2021.02.03

    Read More
  • Packaging and transportation of capsule filling machine packaging The equipment is packed in wooden case, put a certain amount of dry inside the machine, and cover the equipment with aluminum foil bag before packing, seal the aluminum foil bag after vacuuming, and then cover the outer box with plastic bag after sealing. The packing boxes shall be printed with signs such as no upside down, no collision, etc., and marked with the position of forklift insertion. Transport The main machine, electric control cabinet, auxiliary machine and parts box of the automatic hard capsule filling machine are installed in the wooden packing box respectively. In the box are the following technical documents: product qualification certificate, product instruction manual, frequency converter manual. The equipment should be firmly fixed on the transport vehicle in the process of transportation, and no rolling or collision is allowed. The equipment is not allowed to be hoisted. It is only allowed to b

    2021.02.02

    Read More
  • Total 61 pages  Go to Page
  • Go
  info@hanyoo.net
  0086 25 5621 6295
  0086 25 5621 6289
  0086 187 5183 8183
  No. 380 Sanqiaogeng, Gaochun District,
Nanjing, China. 211300

Quick Link

Products

Leave a Message
Contact us

QR Code

Capsule Filling Machine, Blister Packing Machine
Copyright  2016 Jiangsu Hanyoo Pharmatech Co., Ltd. All rights reserved. Capsule Filling Machine, Blister Packing Machine, Cartoning Machine Professional Manufacture.