Structure of capsule filling machine Capsule filling machine structure, the top of the drum is a large volume of empty capsule groove; At the upper end of the rotary cylinder, the outer layer is provided with a feeding pipe, the lower end of the feeding pipe is provided with a door to control the discharge of the capsule, the feeding pipe is near the inner side of the rotary cylinder is provided with a fork, the outer side is provided with a locking rod; The inner layer of the rotary cylinder is provided with a measuring tube, which, in addition to the rotary motion with the simplified body, is vertically moved axially according to the curve of the CAM groove within it. The lower flange of the rotary cylinder is provided with the upper supporting cup fixing mold corresponding to the number of feeding pipes, which can limit the drop of the cap when the empty capsule is opened, and keep the cap in the upper supporting cup mold; Flange flange is above the positioning device, complete t

Scrub of capsule filling machine Cleaning tools: nylon brush, fiber - resistant rag, mop, vacuum cleaner, etc. Cleaner: "Diao Brand" detergent. Disinfectant: 75% alcohol. Preparation of detergent: add proper amount of detergent and drinking water to the cleaning pool, stir thoroughly and set aside. Preparation of disinfectant: a certain amount of anhydrous alcohol and a certain amount of distilled water mixed, fully stirred evenly, reserve. Cleaning method: same type, same specification Cleaning: use nylon brush to collect the powder scattered on the machine and the table in the appropriate container. Recyclable and non-recyclable items should be collected separately. Use plastic bags to seal the hopper before leaving work to prevent accidental contamination. Place the empty capsule back into the capsule container. Collect the broken and empty capsules and the empty capsules scattered on the machine or counter surface and destroy them. Collect broken and filled capsules in

Disinfection procedure of capsule filling machine Conditions of implementation: before each production. Disinfection frequency: before production, after maintenance, when quality problems occur. Disinfection parts: hopper, bucket measuring plate, mold filling system, balance plate and other parts directly in contact with drugs. Site of disinfection: production site disinfection. Disinfection tools: pail, cloth. Disinfectant: 75% alcohol 3% hydrogen peroxide solution (regular monthly use) Disinfecting method: wipe twice with special disinfecting cloth dipped in antiseptic agent. Wash twice with pure water after disinfection with 3% hydrogen peroxide solution. Evaluation of disinfection effect: microbial sampling inspection qualified.

Brief introduction to the development of capsule filling machine The preparation of hard capsules is generally divided into the preparation of filling drugs, capsule filling, capsule polishing, packaging and other processes. Among them, the capsule filling is the key step. The development of the capsule filling machine has gone through three times, the first is manual filling equipment, then semi-automatic capsule filling equipment, and then developed to automatic capsule filling equipment. Manual capsule filling is generally used for small batch production, the production process is completely manual operation, the production process needs a lot of human input, the production efficiency is low, the sanitary conditions are difficult to meet the national GMP regulations, basically has been eliminated. The production process is as follows: the granular drug is laid on an appropriate plane, the knife is spread into a uniform powder layer and pressed tightly, the thickness is about 1

The mechanism of semi-automatic capsule filling machine Used for capsule filling, seeding, powder filling and locking automatically, instead of manual filling, reduce labor intensity, improve production efficiency, domestic or imported mechanism capsule can be used, the filling dose is accurate. It adopts electric and pneumatic joint control, equipped with electronic automatic counting device and computer speed regulating device, and completes the actions of capsule positioning, separation, filling and locking respectively. Adopt three stepless speed regulating motor to drive operation, easy to maintain and operate. The vacuum pump is started and stopped by button instruction, interlocked with AC contactor, equipped with vacuum gauge, throttle valve, display and regulation system pressure. The seeding mechanism is powered by a single stepless variable speed motor. The display of seeding speed automatically runs for one week. The machine is set by a counter (60 times) to

Capsule filling machine load test Load test can be carried out after passing no-load test. Manually run the device, open the capsule holder, and allow the capsule to drain into the capsule plate hole. And adjust the push pawl, pressure pawl and capsule directional seat of the pawl mechanism as appropriate, so that it is on the center. The capsule should be discharged into the hole of the capsule plate smoothly, and the action of the plucking cap, pressing and pushing mechanism is coordinated. The charging powder should run for no less than 1 hour, check the metering device, and adjust it flexible. The difference in the loading accuracy of the powder should not be more than 5%, and it should comply with the provisions of the Chinese Pharmacopoeia. The qualified rate of empty bag row, dial cap and closure is above 99%. The qualified rate of finished products shall not be less than 99.7%. Electrical control is sensitive and reliable. Vacuum can be adjusted freely.

Advance cleaning of the capsule filling machine The capsule filling machine is a special machine for capsule filling. It has direct contact with the powder, and its cleaning procedure will affect the quality of the medicine. After production, the filling machine should be thoroughly cleaned. After production, first cut off the power supply, shut off the vacuum pump and air compressor. Remove powder hopper, empty capsule hopper, cyst feeding plate, upper and lower template, capsular lock roof, etc. and send them to the cleaning room for cleaning. Soak with water first, reoccupy brushs clean with wool brush, rinse with water, wipe the water of surface with towel or place in oven to dry. Clean the surface of the machine and the outlet with wool, and then wipe the surface of the machine, the outlet, the control panel and the electrical dust with towel. Wipe every concave and convex part outside body with towel. Remove the top cover of the vacuum pump, take out the filter

The mechanism improvement of a new type of capsule filling machine The dividing rotary table device of the capsule filling machine includes a rotary frame, a lifting and radial stretching mechanism, an upper module and a lower module. The rotary frame includes an upper rotary table, a lower rotary table and a brace for fixing the upper and lower rotary tables. Rotating frame connected to dividing box output shaft, lift and radial expansion mechanism set in the rotating frame, including the CAM plate, guide, slider, smooth column, column, the module is radial distribution in the wheel around, symmetry in the module under distributed in the rotating frame around, have a seal coating seal rotating frame and lifting and radial expansion mechanism, form a sealed chamber. The output shaft of the indexing box is fixed to the upper rotary table, the upper module is fixed to the periphery of the upper rotary table, the CAM disk is fixed on the machine, and the working face is facing up. L

Basic installation of capsule filling machine Switch on the main power switch. Check the lubricating oil of the main engine and auxiliary engine, and turn the handwheel to check whether the machine is normal. Align the locating pin, install the horizontal guide block to the bottom and tighten the handle on both sides. Install the horizontal guide fork, install the supply fork and tighten the handle and square head bolt (square wrench). Install the vertical supply plate in place and tighten the square head bolt (square wrench). Install the capsule funnel and tighten the handle. Install the capsule bucket and tighten the two fixed handles. Install the condensation thimble, install the condensation thimble pressing plate, and tighten the square head bolt (square wrench). Install clean thimble, eject thimble, remove thimble, install in place and to the end, tighten square head bolt, turn hand wheel, all thimble should be in the center of die hole (square wrench).

How to use automatic capsule filling machine? Before using the automatic capsule filling machine, please check whether all parts of the machine and equipment are in good condition, and disinfect and clean the instrument as required. According to the filling volume and other process requirements, select the appropriate tray, powder or particle filling system specifications. 1. The support is placed parallel to the material plate, and the filling rod is perpendicular to the support, so as to ensure that the filling rod can easily enter the filling hole of the material plate. Loosen the fixing screw and lock nut, rotate the screw to the desired height, calibration lever has scale, then tighten the screw and nut, fill seat height adjustment is finished. 2. After all the safety configurations have been configured and adjusted, the machine should be rotated 1-3 times in the absence of capsules and drugs to turn the machine to the working direction and turn it back with the hand whee