News Room
You are here: Home » News Room

aluminum-plastic packaging machine

The articles shown below are all about the aluminum-plastic packaging machine, through these related articles, you can get relevant information, notes in use, or latest trends about the aluminum-plastic packaging machine. We hope these news will give you the help you need. And if these aluminum-plastic packaging machine articles can't solve your needs, you can contact us for relevant information.
  • The operation of aluminum-plastic packaging machine Some advanced technology of aluminum bubble cover packaging machine equipped with a variety of automatic monitoring devices, can play a variety of protection, in the discovery of the following problems automatically stop the machine operation (1) Open the safety cover; (2) insufficient pressure of compressed air; (3) the heating temperature is not enough; (4) PV C film or aluminum foil is used up; (5) The packaged medicine is used up (6) Mechanical overload at some stations; (7) Circuit overload. The machine cannot be started until the following problems are resolved (1) The safety cover is not completely closed; (2) insufficient pressure of compressed air; (3) the heating temperature is not enough; (4) Lack of PVC or aluminum foil film; (5) Overload or other faults have not been removed; (6) The setting of function keys is wrong, and the emergency stop/start key is not reset.

    2021.10.21

    Read More
  • Cleaning of aluminum-plastic packaging machine Automatic plate aluminum plastic packaging machine is qualified tablets, capsules for packaging of the main equipment. As it is in direct contact with the surface of the product, its cleaning procedure directly affects the quality of the product. Both before and after production to the aluminum packaging machine for thorough cleaning. After production, cut off the mechanical and electrical power source of aluminum plastic packaging, cut off the PVC and aluminum foil remaining on the machine, take them off and put them into the box for sealing. Wipe the powder and stain on the surface of PVC guide column, aluminum foil guide column, control panel, forming die surface, die hole, blow plate, cut, discharge port, traction template and so on with a clean wet cloth. Clean the powder and dirt on the upper and lower heating plates with a copper brush. Clean the brush, brush roller and four walls in the charging tank of the powder brush board

    2021.09.15

    Read More
  • Cleaning work of aluminum-plastic packaging machine Automatic plate aluminum plastic packaging machine is qualified tablets, capsules for packaging of the main equipment. As it is in direct contact with the surface of the product, its cleaning procedure directly affects the quality of the product. Both before and after production to the aluminum packaging machine for thorough cleaning. After production, cut off the mechanical and electrical power source of aluminum plastic packaging, cut off the PVC and aluminum foil remaining on the machine, take them off and put them into the box for sealing. Wipe the powder and stain on the surface of PVC guide column, aluminum foil guide column, control panel, forming die surface, die hole, blowing plate, incision, discharge port, traction template and so on with a clean wet cloth. Clean the powder and dirt on the upper and lower heating plates with a copper brush. Clean the brush, brush roller and four walls in the charging tank of the powde

    2021.09.07

    Read More
  • Heat sealing process of aluminum-plastic packaging machine At present, the heat sealing process of aluminum-plastic packaging machine has attracted much attention in the market. The technical personnel of aluminum plastic packaging machine said that the process of aluminum plastic bubble cap packaging machine -- heat sealing, is in the forming film bubble cap filled with good drugs, covering the film is covered on it, and then the two together. Its basic principle makes the inner surface heat, through pressure to make it close contact, forming a completely welded effect. The heat sealing process has two forms; Roller press and plate press. Among them, the roller type is the packaging material by rotating between the two rollers, so that the continuous sealing. Technicians remind that the residence time between the two rollers of packaging materials is very short, so to get the ideal heat sealing effect, it is necessary to adjust the speed of the slow roller, or carry out sufficient p

    2021.06.16

    Read More
  info@hanyoo.net
  0086 25 5621 6295
  0086 25 5621 6289
  0086 187 5183 8183
  No. 380 Sanqiaogeng, Gaochun District,
Nanjing, China. 211300

Quick Link

QR Code

Capsule Filling Machine, Blister Packing Machine
Copyright  2016 Jiangsu Hanyoo Pharmatech Co., Ltd. All rights reserved. Capsule Filling Machine, Blister Packing Machine, Cartoning Machine Professional Manufacture.