The scope of use of blister packing machine 1, the use of new domestic high-power transmission mechanism, driven by the chain drive shaft, avoid the error and noise of other gear transmission. 2, The electrical appliance adopts the imported control system, can be configured according to customer requirements, the lack of material leakage and lack of grain detection and elimination device (Omron sensor). Adopt imported frequency conversion governor. 3, The whole machine adopts segmented combination: PVC forming, feeding, hot sealing for a section, tropical aluminum cold forming, hot sealing, punching for a section can be separated packaging. 4, The use of photoelectric control​ system, PC, PTP, tropical aluminum packaging automatic feeding, automatic waste side receiving device, to ensure the long distance and multi-station synchronous stability. 5, can be equipped with photoelectric detection and correction device, with imported stepping motor traction, image and text plate printi

Work content of blister packing machine 1. Turn on the main power switch, connect the compressed air and the cooling water. 2. Turn on the "heating" switch, and the host starts to heat. 3. check the batch number is correct, if the army will change the batch number. 4. When the heating temperature reaches the set value, press the "dot action" button to open the lower die. 5. Lift up the heating plate, open the "step clamping" button, pass the PVC through the molding mold and the clamping cylinder, and wear the PVC outside the body. 6. Put down the heating plate, press the "Start" button, adjust the rotation of the "host speed regulation", make the host run at a low speed. After the PVC is formed, go out about 3 meters, press the "stop" button to stop the host. 7. Obact the forming condition of the bubble cap, whether it is uniform and straight, and whether it is bent on the length of 3 meters. 8. Cut the end of the PVC with scissors, turn it 180 degrees and put the PVC into the

The operation content of blister packing machine 1. The machine is fully enclosed, and the parts that contact with the drug are made of high quality stainless steel plate, which is smooth, smooth and without edges and corners. The equipment itself does not pollute the production environment, and does not pollute the drugs, and conforms to the GMP standard. 2.PVC molding is plate-type positive pressure molding, which is composed of forming die and blowing die. The forming mold moves downward, and then moves downward 0.5 ~ 1mm after contacting the blowing mold. The air pressure is 0.35 ~ 0.5Mpa. When the forming mold moves upward 0.5mm, the blowing stops, and the forming is completed. 3. The clamping step adopts the swivel arm type double clamping mechanism, two pairs of fixed clamping does not move, a pair of reciprocating movement clamping PVC is sent into. Adjust the length of the swing rod and connecting rod, so that the stepping distance can meet the requirements of the plate siz

Packaging process and technology of blister packing machine In the process of blister packing and processing, a forming die, a blister cutting die and a heat sealing tool are needed. The process steps are: (1).0.127~0.38mm plastic film sheet, in the epoxy resin mold or inner cold aluminum mold, using heating and vacuum method to form a bubble bubble cavity; (2). After die-cutting, heat release sealing appliance; (3). Put the product into the cavity of the bubble cap; (4). The card board coated with heat sealing flux type coating, face down to the heat sealing appliance, the use of positioning pin positioning, to ensure that the cardboard and the bubble cap accurately bonded; (5). The heat sealing tool is moved to the heating sealing zone, and the film is bonded to the film paper after pressurized heating (120~204℃) for 1.5~3S. Heating sealing can be divided into direct method and indirect method (1). Direct heating sealing method The tool for directly heating the edge of the bu

Function characteristics of blister packing machine 1. Adopting the latest type of high-power transmission mechanism in China, the main transmission shaft is driven by the chain, which is free of error and noise of other gear transmission. 2.The electrical appliance adopts the import control system, can be configured according to customer requirements, lack of material leakage repair device and lack of grain detection and elimination device. 3. The whole machine adopts segmented combination: PVC forming, feeding, hot sealing for a section, tropical aluminum cold forming, hot sealing, punching for a section can be separated packaging. 4.The use of photoelectric control system, PVC, PTP, aluminum packaging automatic feeding, waste edge automatic punching device, to ensure the long distance and multi-station synchronous stability. 5.can be equipped with photoelectric detection and correction device, with imported stepping motor traction, image and text plate printing packaging, opti

Safe operation of blister packing machine Aluminum packaging machine is almost the necessary machinery for any enterprise, but many enterprises have had accidents, property losses fall next, mainly this equipment is easy to cause physical injury to workers, common burns and cuts. Scalds mainly occur in PVC thermal forming station, heat sealing and pressing station, especially in heat sealing and pressing station. Due to the large difference in the shape and size of materials in domestic equipment, the proportion of falling into the bubble cap is low, and the bubble cap needs to be manually filled or picked up, which is easy to cause hand burns. It is suggested that the workers should pay attention to these two stations. The manufacturer has posted warning signs on the stations that are easy to burn. The cutting mainly occurs in the cutting station. This station or up and down cutting, or left and right cutting, according to the installation of the cutter. Cutters used for a pe

The flat plate structure of blister packing machine Plate type blister packaging machine operation process and execution of work: molding plastic is heated to softening at plate type preheating to remove plastic state, servo traction to the plate type forming disassembly, dominating shorten air will soften hard blow molding of plastic (or stamping molding) into a blister, remove the filling materials will be filling into the bubble, and then transfer to a plate type sealing removal, at the appropriate temperature and pressure, will cover plastic plate and aluminum foil sealing, then sent to the typing, stamping and punching disassembly, with batch number, pressure out of the broken line, cutting into a regulation the size of the plate. That is, molding plastic hard sheet unwinding → preheating → blow molding → material filling → sealing aluminum foil → batch number → pressure break line → servo → punching and cutting → waste collection. Some drugs need to avoid light packaging, the

The use of vacuum pump for blister packing machine Start: the vacuum pump can be started after the oil level is determined. The vacuum pump must be rotated backward after the first starting and each wiring change. Operation: before normal work, the inlet pipe valve should be closed to make the pump operate for more than 15 minutes under the limit pressure state, so that the water vapor in the gas can be effectively extracted. The motor should not be started frequently (less than 6 times/hour). (Note: When the pump is running normally, the surface temperature of the oil separator, pump body and pump cover will exceed 70℃. Do not touch with your hands. The pump cannot be refueled while it is running. Limiting pressure measurement; The ultimate pressure should be measured directly at the suction port of the pump with a compression vacuum gauge. Pump once used, long term use after use, new oil should be closed after at least 1 hour of operation, so that the pump to reach the worki

The process of blister packing machine 1. Before starting, manual transfer should be free of jamming phenomenon. 2. Switch on the power supply with the key and set the temperature of the two temperature control meters as required. Blowing temperature: 140--160℃ Heat sealing temperature: 190--210℃ 3. Connect 380 volt power supply. After starting the machine, the bubble blowing roller should turn clockwise. 4. Install PVC sheets and aluminum foil on their respective supporting shafts. 5. When the two meters reach the set temperature, the following operation can be performed. First, the PVC sheet passes through the small guide roller, the inner heating roller passes through the bubble suction roller and the smooth roller, and then the PVC head is pulled by hand. After starting the machine, the PVC bubble forming is more than 3 meters long, and then the hard sheet is put through the platform, the bubble blowing roller, the traveling roller and the feed roller into the

Adjustment of the CAM of bubble cap machine Valve CAM on the shaft of the installation sequence: from inside to outside in turn for traction clamping cylinder CAM, cylinder CAM stop, molding blow CAM and molding cylinder CAM. When the return position of the heat sealing CAM linkage in the heat sealing die is very low, the valve CAM shall be installed according to its position. Traction machinery in the CAM traction clamping cylinder control valve slightly earlier than the CAM opened. When traction machinery traction is static, the return of the stop cylinder is clamped. After the molding mold and the blowing mold are closed, the blowing CAM opens the machine control valve, that is, blowing molding. Forming cylinder rise should be synchronized with the heat sealing CAM. Clamp of the general process is: traction after plastic sheet, plastic piece positioning cylinder to loosen, immediately manipulator to traction, manipulator in place after the stop, plastic piece posit