The finished product of blister packing machine Appearance of the finished package: The blister should be full, smooth and clean; The batch number in the plate should be clearly identified and the position should be accurate, and there should be no pollution of the plate phenomenon; PVC and aluminum foil sealing place should be tight, smooth, clear pattern, no wrinkling, pressure wear phenomenon; PVC and aluminum foil at the corner of the plate shall not be separated; No burrs at the edges and corners of plates. Dimensions of finished package: The size difference of the plate length and the plate width is ±0.3mm. The sealing distance between the blisters is not less than 2.5mm, and the sealing distance between the edge of the blister and the edge of the plate and the tear line is not less than 2.5mm. Sealtightness of finished package: Plate sealing is tight, no liquid infiltration blister or sealing layer. Filling rate of finished package: There shall be no lack

Tablet press mold processing About processing, blanking (before heat treatment), grinding plane, tablet type, coarse car size, quenching, tempering, cleaning, external grinding, centerless grinding, flat grinding, external grinding, polishing, inspection, packaging, the general process is like this. Says the most common mold and cheap, namely ZP series, using the bearing steel processing mould, they are what kind of process, the previous file process take not processing, rough turning directly the file size (piece of cup noodles is also direct car), hardening, grinding, centerless grinding, flat grinding, polishing, inspection, packaging. This process can not maintain the consistency of the sheet (because it is out of the car) and then temper the next process, the internal stress of the material elimination. The following process will continue. The mold process of high-speed tablet press is basically the same as the above, individual manufacturers temper the mold after quenchi

Operation requirements of blister packing machine The connection of each part of the packing machine should be firm and reliable, and the air control, air passage and water passage system should be smooth, and there should be no leakage. During the operation of the packaging machine, each moving part should be coordinated, flexible, accurate and in place, and the movement state switch of the moving mechanism should be flexible and reliable, without dead point, hard magnetic impact, stuck phenomenon. There should be no abnormal noise during no-load operation of the packaging machine, and the noise pressure level should not be greater than 82dB (A). The packing machine should be equipped with batch numbering device, the structure is easy to disassemble and assemble. The tear line of the packaged product should be kept intact without penetration, consistent in depth, and easy to be torn by hand.

Tablet press to produce abnormal sound how to do? 1. Synchronous belt is not parallel, resulting in friction and abnormal sound. The solution is to adjust the motor so that the synchronous pulley on the spindle is parallel to the synchronous pulley on the worm shaft. 2. The reduction box is short of oil, resulting in increased friction and noise. The condition of lubricating oil should be checked regularly. 3. Slight friction between the turntable and the baffle plate (feeder) produces noise. The solution is to adjust the gap between the baffle plate (feeder) and the turntable; 4. If individual bearings are short of oil or damaged, lubricating oil should be applied or damaged bearings should be replaced; 5. The punch rod plug is not flexible in punching and rotation. The solution is to press the tablet room regular clearance, cleaning the rod.

Capsules machine pressing product export adjustment The total length of the capsule after pressing must be adjusted according to the requirements of different specifications and different lengths of the capsule, or when replacing the capsule. The gap between the pressing baffle and the very high point of the capsule in the module should be 0.2-0.3mm (measured with a feeler ruler), which is adjusted by the thickness of the replacement washer. The adjustment method of the height of the push rod is to put the closed capsule into the module, adjust the length of the CAM connecting rod to adjust the length of the screw, so that the push rod movement to a high position, the column pin against the lower part of the capsule shall prevail. In the filling process, if it is found that the capsule is not closed properly, such as too long at the end of the lock closure, too short capsule deformation. Careful readjustment is needed at this point. Tighten nut after setting. There is a gap betwe

Performance test of tablet press Test 1: check whether the connection of electrical and vacuum dust removal meets the requirements, and the lubrication of each part must meet the requirements. Check the die according to the die quality standard and install the die according to the instruction. Turn the hand wheel to rotate the table 2-3 times to make sure that the middle die and the regulating wheel can slide flexibly without collision and hard rubbing. Safety protection device, hopper installation meets the requirements, emergency brake system should be sensitive and reliable. Check the motor steering, do not reverse, and confirm that installation validation has been performed and approved. Test 2: No load operation for 60 minutes, noise no more than 82dB (A). All connectors and fasteners are connected reliably without loosening. Smooth operation, no abnormal vibration and impact sound. Clutch and gearwheel adjust flexibly and reliably, and position correctl

Blister packing machine price and benefit analysis (1) Technical performance, including production speed, finished product quantity, quality, yield, consumption of raw materials, power, degree of automation, safety, impact on environmental protection. (2) Applicability, whether the complete supporting system of the whole machine is complete, whether the interface device with extended function is reserved, whether it has the same technical performance for multiple varieties and specifications, whether it is convenient to operate and change the mold in use, what are the requirements for the applicable environmental conditions, and the degree of adaptation to raw materials. (3) the reliability of equipment is prone to failure in the process of work, whether at work requires constant adjustment, whether to remain unchanged for a long time continuously, the technical performance of the machine operator level in the power, voltage, environment changes in the conditions, whether the

The use of the tablet press Before the use of the die must be strictly checked, there can be no cracks, missing edges and hair and other phenomena, such as forced use will bring damage to the machine. Die life is generally based on one million times of tablet design, when the extended use of the damage rate will be greatly increased, such as rupture will damage the feeder or other parts of the accident. Feeder and turntable work surface must maintain a certain gap, that is, 0.05-0.1 mm. The clearance is too large to cause powder leakage, too small will make the feeder and the rotary table friction, resulting in metal powder mixed into the powder, so that the pressed out of the tablet does not meet the quality requirements, become scrap. The vacuum cleaner must be shaken several times per shift, and its powder storage hopper must be cleaned in time to prevent blockage of airflow channels. If automatic stop is found, immediately turn off the power for careful inspection. I

Labeling requirements for blister packing machines Marks, marks The cold water pipeline and air pipeline of the packing machine shall comply with the provisions of GB 7231. The power cut-off switch of the packing machine adopts switch isolator, isolator or circuit breaker to isolate the electrical equipment from the power supply. There should be only one "off" and "on" position, which should be clearly marked with "O" and "", and should comply with the provisions of GB5226.1-2002. The identification of the wire of the packing machine shall comply with the provisions of GB 5226.1 -- 2002. The positions of the control devices and switches of the packaging machine should be marked by numbers, words or other visual methods in accordance with the provisions of GB 9706.1-1995. The buttons used by the packing machine shall comply with the provisions of GB 5226.1 -- 2002. The color code and status of the indicator light and display used to show the working status of the pa

Appearance inspection of tablet press Equipment Appearance Inspection Verification method: carefully check the appearance of each component of the equipment. Check whether the structure of the equipment is easy to clean and repair, whether the welding is firm and pressure safe, the welding surface is smooth and smooth, and there is no dead Angle, and there is no bump, deformation and scratch on the surface of the equipment. Qualification requirements: the welding equipment is firm and safe, the welding surface is smooth and smooth, no dead Angle, argon arc welding needs polishing; The structure of the equipment is easy to clean and repair, and the appearance of the equipment has no defects, and there is no damage during transportation. Person in charge: After careful inspection by equipment management personnel, fill in the appearance inspection record of the tablet press. The material to confirm Verification method: check all parts of the equipment and confirm against the attach