Material device of bubble cover packaging machine Aluminum-plastic drum: aluminum foil drum and plastic sheet drum are two parts. The drum is mainly composed of the drum body, stator inside and outside, brake ring and adjusting nut, etc. Both ends of the drum body are supported by rolling bearings on the supporting shaft, which is the rotating part of the drum. When the plastic film or aluminum foil is pulled, the coil loaded on the drum is driven to rotate freely. The stator is divided into inner and outer stator, and the sliding sleeve is set on the cylindrical surface outside the cylinder, and fixed at any position of the cylinder body by fixing screws, to install and fix coils of different widths. The brake ring is set on the inner and outer cylinder surface of the drum body and fixed on the support plate. It is the static part of the drum and used for braking the drum body. Tightening or withdrawing the four adjusting screws on the outer circumference of the brake ring can incre

Basic operation of bubble cover machine PVC hard, aluminum foil volume installation: unload the film reel on the compression nut and the retaining sleeve, the PVC hard or aluminum foil volume set in the adjustment sleeve, installed on the retaining sleeve and the compression nut and screw compression nut, so that the film volume on the adjustment sleeve can not be loose and rotation; Loosen the back cap and turn the adjusting nut to align the CENTER of the PVC roll with the center of the heat sealing roll (250mm away from the body). When installing, measure the inner part of the roll from the body 125mm with the steel ruler; Adjust the brake screw tightness, PVC tension adjustment in 0.5~1kg tension, and aluminum foil tension adjustment in 1~2kg tension. Placed PVC plastic belt, through the upper and lower heating plate mold to dividing feed roller and pressure roller, after being met the requirement of the temperature and pressure, press the start button, at this point, the device d

The structure principle of bubble cover packing machine Blister packaging machine structure by the machine base, forming mechanism, feeder, hot seal indentation mechanism, punching mechanism, traction manipulator and electrical control parts. Main drive of cycloidal pinwheel reducer motor drive, speed reducer output shaft sprocket drive spindle chain wheel on the run, driven by sprocket chain traction CAM again, so as to realize the intermittent reciprocating motion of mechanical chains, suction blister and composite molding CAM operation process, adopting cylinder as prime mover, realize molding mould and checker for lifting up and down movement. The aluminum-plastic bubble cover packaging machine needs the medicinal PVC to be heated and softened by the heating plate into the forming mold, which is positive pressed by compressed air; And aluminum aluminum needs medical cold forming composite aluminum and its cold punch stamping can be formed, through the universal feeder filling ca

Blister packaging machine production position requirements 1: Site clearance inspection confirmation before production: check that the operator's tooling, work shoes, masks are clean, wearing, and personal hygiene meets the requirements. Pay special attention to checking employees. Check production operation room to meet production process requirements. Check the production site (ground, table, container, equipment, guide rail, etc.) no unrelated to this batch of production. Check whether the equipment and container are in good condition and clean. Check whether there is verification certificate, and within the validity period. Calibrate the weighing instrument. Make clearance check and confirm record before production. 2: according to the issued, take the batch record to the material station (a) take out the corresponding material with the material list and the batch record, take the inner package material handover sheet (two) receive the packaging material, check the receiving pack

The prospect of blister packaging machine DPP plate type aluminum bubble cover packaging machine is a multi-functional packaging machine which can automatically complete bag-making, material metering and filling, exhaust or aeration, sealing and cutting with flexible packaging material that can be heat sealed. This kind of packing machine is suitable for a wide range of powder, granular, flake, block, material, fluid and semi-fluid and gas materials. It is one of the packaging machines with rapid development and widespread application in recent decades. And their applications are expanding and packaging speed is increasing. DPP type flat aluminum bubble cover packaging machine to complete a function of different actuators function is the same, but its performance and specifications are different. If the different parts of a function are regarded as a module, the different parts in the module can be selected to form different types of products with different specifications, so the mod

Function and characteristics of bubble cover packaging machine The whole machine can be packaged separately to enter the 2.2m elevator and the split purification workshop. Mould and guide rail adopt independent design, change mould only need to replace the whole guide rail, mould pressure plate clamping, loading and unloading is very convenient. Suspension operation platform design, operator in the use of the process of safety and maintenance of cleaning machine when convenient. The modular design of the station structure realizes the digital display control during the adjustment of each station, which adapates to the diversified needs of the indentation form and ensures the clarity of the indentation and batch number. Equipped with photoelectric compensation device, it can be used for image and text matching of printed aluminum foil. The main motor adopts frequency conversion speed regulation: according to the length of stroke and the filling of the material and other factors to

Development prospect of bubble cover packaging machine Although, in recent years, the development and research of domestic high-speed aluminum bubble cover packaging machine is very fast, and the quality and performance of similar products of some manufacturers are basically equivalent to foreign products, but foreign products are also developing rapidly. The following development directions can also be used for reference by similar domestic manufacturers. (1) Material selection and structure (pay special attention to details) must meet the requirements of GMP, the equipment should not produce pollution, nor will it cause cross-pollution to the surrounding environment. (2) The structure should be simple and clear, avoid tedious structure as far as possible, easy to disassemble and assemble, and easy to clean, clean, disinfection (or sterilization). (3) The control system has the functions of process state, working performance curve, fault alarm, online control, remote monitoring an

Operation of vacuum pump of bubble cover machine Before normal operation, the inlet pipe valve should be closed, so that the pump in the limit pressure state of operation for 15 minutes, so that the water vapor in the gas can be effectively extracted. The motor should not be started frequently (less than 6 times/hour). (Note: the surface temperature of oil separator, pump body and pump cover will exceed 70℃ when the pump is in normal rotation, do not touch with hands; Pumps cannot be refueled while running.) Ultimate pressure measurement; The ultimate pressure should be directly measured by compression vacuum gauge at the suction port of the pump. Q pump should be used for the first time, used after long-term use, after changing the new oil, the air port should be closed for at least 1 hour after operation, so that the pump reaches the working temperature and the pump oil is fully degassed after the pressure is measured. Vacuum pump oil: The vacuum pump should use the vacuum pump oi

Bubble cover packaging machine production clearance 3.1 After the production of this batch, the post operator shall change the batch number record, and the post leader shall inform the external contractor to change the batch. The next batch of packaging can be carried out only when it is confirmed that the current batch of packaging has finished. 3.2. Transfer the remaining PVC hard sheets and aluminum foil to the packing material storage room in time during the large clearance, and check the collar amount, usage amount, residual amount and loss amount of all PVC hard sheets and aluminum foil. 3.3 When changing the variety or specification, the remaining PVC hard sheets and aluminum foil shall be returned to the warehouse. 3.3.1 Fill in the material return form according to the checked remaining quantity. 3.3.2 In the packing material storage room, the materials shall be discharged in the opposite order when entering the inner package and returned to the warehouse. 3.3.3 The ware

Blister packaging material adhesive Blister packaging is the main packaging form of solid dosage form of health food and medicine in China. Among them, the medicinal aluminum foil is pure industrial aluminum foil as the base material, on the surface of the printed word pattern and coated with protective agent, and on the other side coated with adhesive. The purpose of coating protective agent is to prevent the surface printing ink layer wear, but also to prevent aluminum foil winding, outer ink and inner adhesive contact caused by drug contamination. The purpose of the adhesive is to bond the aluminum foil to the plastic sheet, so that the drug is sealed. Currently used adhesives are mainly divided into single component glue and two component glue. The components of single component glue are mainly natural rubber and nitrocellulose fiber, acrylate fees, because the main agent is an elastomer, coupled with adhesives as additives, with organic solvents into emulsion, it has dry, hot mel