Feeding for the capsule filling machine In the pharmaceutical field, the drugs in capsules are mostly powder or particles that stimulate the esophageal and gastric mucosa, or have bad taste, which are volatile, easily broken down by oral saliva, and easily inhaled by the trachea. These drugs are packaged in capsules to protect the drug as well as the digestive organs and respiratory tract from damage. Removing the capsule can lead to drug loss, drug waste, and reduced efficacy. In addition, some drugs need to be dissolved and absorbed by the gut, and the capsules can protect the drug from being destroyed by stomach acid. At present most of the capsule filling machine filling powder, existing capsule filling machine feeder is usually at the top of the capsule filling machine, need workers to get a bag of a bag of finished product capsule is placed on the top of the capsule filling machine, and then pour into the feeder, in general, about two meters tall machine need to use the lad

Blister packaging machine procedures 1. Open the green indicator button, and open the upper, lower and heat seal respectively at the working position. This thermometer controls the forming temperature, the second thermometer controls the heat seal, and the forming and upper and lower heat seal of the temperature preset temperature regulator. 2. During the compression molding of the low induction roller, the temperature of the heating plate is mainly in the position. Before starting the machine, change the shape of the PVC blister plastic according to the mold base, and observe whether the air cylinder seal has the heat of aluminum foil, which will lead to blanking. Notice if the plastic moves left or right. In case of deviation, the movement direction of roller seat should be adjusted. 3. Moderately open the feeder switch after the hot sealing and blanking is normal, so that the packing items enter the feeder. If any product is brought into the hot sealing mold, the synchroniz

Pressure adjustment of the tablet press First, open the main switch, and then press the pressure (decompression) button, pressure, decompression repeatedly, the residual air out of the tube. Punch pressure is adjusted according to material nature and punch diameter. For the material with large blade diameter, low viscosity and not easy to form, the larger blade impact pressure can be obtained by programming. Plate diameter, high viscosity, easy to form, stamping strength is small. When adjusting the filling volume, the left hand steering wheel controls the weight of the workpiece pressed by the left hand pressure wheel. When the steering wheel rotates clockwise, the filling volume increases, that is, the filling depth increases. When the steering wheel rotates counterclockwise, the filling amount decreases, that is, the filling depth decreases. The central adjustable steering wheel controls the weight of the parts pressed by the direct press wheel. When the adjustable handwhee

Other factors affecting the capsule filling machine Other factors affecting the capsule filling machine generally include environment and transportation. The environment A fully enclosed environment is mainly reflected in temperature and humidity. The ideal relative humidity condition is 35-65%, and the temperature is 15-25℃. Too low humidity will make the shell brittle and easy to decompose. A capsule with high humidity will become sticky and deformed. Too high a temperature will cause thermal damage to the capsule. The transportation In the process of transportation, if the hollow capsule is impacted, the deformation of the capsule may hinder the filling of the capsule in the production process, affecting the production efficiency and product quality. To ensure the quality of the capsule products, the first to ensure that the production conditions meet the requirements, reasonable transportation. Now, with the continuous improvement of filling technology, the degree of automati

Liquid blister packaging machine Liquid filling machine Flat aluminum foam packing machine suitable for honey, jam, cheese, salad sauce, tomato sauce, chocolate sauce, perfume, essence, facial mask, condom, lotion, face cream and other aluminum foam packing. The machine is compact in structure, beautiful in appearance, stable in operation and simple in operation. It adopts internal heating to make PVC material heated evenly, and the blister is formed firmly. It is an advanced blister packaging machine in China. Automatic traction of the machine air clip, through the photoelectric eye detection position, the signal is transmitted to the pneumatic valve, control the air clip automatic start stop, walk equal distance. Automatic feeding and waste collection of the machine, through the photoelectric eye and servo motor, to achieve automatic feeding and DPP-170 and DPP-170 or more models of automatic waste collection. Automatic production count, through the detection of automatic

The operation skill of the tablet press 1. Before use, all containers, oil holes and friction surfaces of the press should be filled with lubricating oil. When running without load, oil film should be applied to all friction surfaces to extend the service life of the machine. 2. Before starting the electric compressor, several tablets must be manually tested before and after each shift to ensure the service life of the mold. 3. Storage die: After cleaning, apply a layer of food grade lubricant, put it into a special protective box or die storage box, and put it on the shelf. 4. Filter the material before pressing to prevent the material from producing flake, flake and flake weight difference during pressing. 5. Select the mold type: The correct selection of the mold type is the first step to successful stamping. For example, chewable tablets must be very hard and easy to chew; Because thin film coating is required, a slightly concave shape can be chosen. Due to the absen

The working process of the capsule filling machine Capsule filling machine is intermittent movement, the hole disc automatic capsule filling machine is completely closed in the filling and rotating parts, easy to clean, the upper and lower modules one-way movement into, imported polyurethane sealing lip, clean blowing induction module combined, to ensure that there is no dust, high-speed locking device is equipped with dust collection device. The hopper of the capsule filling machine is inserted into the hollow capsule to seed the tube. There is a switch under the seeding tube. While the seeding of the pipe is geared under the department's leadership, a touch switch is placed under the action of the iron to release the capsule. Has been under the capsule to comb the capsule by function forward to push board, compression of capsules capsule head pushed down and back, empty air suction capsule, comb downward pressure compression, capsule by air suction mould, because there is a sma

Pre-work procedure of blister packaging machine 1. According to the safety electricity standard, turn on the power for lighting. When the test is completed, turn on the power to ensure access to the ground wire and start the main motor. 2. Water connection: The cooling water enters according to the signal board on the fuselage seat. Whether the outlet leaks or not shall be subject to the patency of water inlet and outlet. 3. Air pump: Connect the air compressor pipe to the air plug and open the air compressor at the same time. Air pressure can only be used if the pressure is greater than 0, 6-0,8mpa. 4. Refueling: Add oil to the box and transmission. The amount of refueling is about two thirds of the box capacity. 5.PVC plastic feeding shaft: Adjust the inner and outer taper nuts to make the mold run to the feeding point. After the PVC plastic passes through, the material support will be opened and pressed. Please note that the PVC plastic on the surface of the sheet is

Rotary press punch installation Before the punch is installed, the hopper, feeder and feeder stand must be removed and the turntable and rotary mounted punch should be cleaned, bit by bit, and prepared according to the installation steps. The fixing of screws outside the frame of the middle die the main steel frame is flat with the outer circle to prevent the punch from colliding too tightly with the screw fixing plate and frame. It should be placed flat with the middle die beating rod gently hammered in. The floor plan of the opening should not be higher than the floor plan of the turntable, should meet the conditions, and then tighten the screws. Up-stroke device: The tongue plate is inserted on the opening gap of the guide rail, the middle rod is greased, some oil is added in the running toolbar, one by one, tighten the rod with thumb and forefinger, check the flexible rotation of the upper and lower mold, no scratch problem can occur, the tongue plate must be removed after

The operating point of the capsule filler When the capsule filling works normally for a long time, direct contact with drugs should be adjusted, and when the drug batch is changed or interrupted for a long time, it should also be cleaned. A proper amount of lubricating oil/grease shall always be provided to the driving mechanism under the working surface of the machine tool to reduce wear of moving parts. Check the oil content of the main transmission once a month, supplement it in time when it is insufficient, and change the lubricating oil every half a year. As a rule of thumb, you should use oil. Clutch is the traditional overload safety protection, the clutch should not slip, but due to long-term use may appear slip phenomenon, when the clutch slip phenomenon, may have to tighten the nut to ensure the normal operation of the machine, for the purpose of protection. In the filling process of hard capsules, the vacuum separator of the vacuum system mainly sucks the caps