Vacuum feeder for capsule filling machine Since the 1980s, the hard capsule filling machine has been used to produce drugs, because it involves health, safety and drug control, which is an important means, mainly through several processes: from manual stair delivery to conveyor delivery, rotary positive pressure vacuum automatic transport, and cross-layer pneumatic dead weight transport. The development of these processes shows that their loading methods have been improved with the development of times and the updating of technologies. At present, capsules produced by domestic pharmaceutical companies have been used, only a few small enterprises still use manual filling or other ways to charge, and most of them use automatic charging. Compared with normal vacuum degree, vacuum filling prescription method has the following advantages: Hopper integrated vacuum power supply, compact structure, dust-free, safe and hygienic, low noise. Simple installation, can be installed anywh

Common packaging machinery Bag filling and sealing machine The main processes of the filling and sealing machine are bag forming, filling, sealing and cutting. The packaging materials used are mainly film products, such as plastic film, paper, aluminum foil, composite film, etc. Hot forming packaging machinery According to the molding process of the packaging container, the hot forming packaging machine is divided into blister packaging machine and stick body packaging machine. Blister packaging is one of the most widely used packaging. This is a packaging method in which the product is sealed in a pre-formed blister with a bottom plate. Blister packaging is similar to blister packaging, except that blister packaging products are molded by general molds, while blister packaging is molded by special molds. The fitting package can make the product fixed, and the product quality is not affected by the collision during the cycle. Shrink packing machine tensile membrane after guiding p

Common problems with tablet presses Slide or replace the triangular belt of the tablet press After the belt slider stops, open the side plate and adjust the adjusting screw to fix the motor slider. When the force is applied between the two wheels, the belt should be 10-15mm lower than its original height. When the bottom of the triangle is near the bottom of the plane or touches the bottom, when the sail line is exposed to break, when the belt rubber is broken, the belt should be replaced. High temperature automatic tablet press Reducer high temperature: it is recommended to contact hands normally, not hot for normal. Stop to check if the radiator is blocked. If it is, clear the channel. Check if the oil level is too high or too low. The standard oil level should be in the middle of the oil level viewing window or in a clearly visible position. If the oil is dirty, you can replace it. High temperature of motor: it is recommended to touch hands at room temperature. It is

Disinfection instructions for the capsule filling machine Instructions for disinfection of capsule filling machine: Times of disinfection: disinfection before production and after maintenance. Disinfection tools: dishcloth, bucket. Disinfection site: Disinfect on site. Disinfection method: Equipment parts should be cleaned and installed according to the equipment operation standard; Wipe twice with a cloth soaked in 75% ethanol or 3% hydrogen peroxide. Evaluation of disinfection effect: whether it conforms to microorganism sampling regulations; 75% alcohol and 3% hydrogen peroxide are used weekly. After hydrogen peroxide disinfection, scrub twice with pure water; Fill in the disinfection record, indicate the word of disinfection, indicate the time of disinfection; If used for more than 3 days, disinfect again. Cleaning and storage of disinfecting tools: Clean and dry the tools in the cleaning room according to the cleaning procedure of the cleaning tools and store the

Classification of packaging machinery The most commonly used classification method is according to the packaging process to the classification, can be divided into direct packaging machine and auxiliary packaging machine. Packaging machinery that completes packaging operations such as packaging, filling and filling is called main packaging machinery or main packaging machinery; The packaging machinery engaged in cleaning, drying, testing, sealing, measuring, transportation, stacking is called auxiliary packaging machinery. Packing machine: The packing machine is used for product packing. According to different technology, it can be divided into kink packing machine, pillow packing machine, folding packing machine, envelope packing machine, horizontal packing machine, etc. Packing machine: Packing machine is used to pack powder or particle into solid goods. There are two kinds of filling machines: direct filling machines and bag making machines. The direct filling machine is made of

Problems and solutions of tablet press No fuel supply for rotary tablet press: First, turn off the power of the machine and remove the oil pump cover and oil tank side panel from the machine. Check whether the oil pump is inverted and the oil tank leaks oil. Oil pipe blockage, the crude oil washing pipe valve removing or see if there is foreign body ball tube after cleaning, use mouth to blow into the mouth of the gas is not leak after the oil rod, and fixed the body of the tank farm pump, one way to remove any tube and pipe screw filling oil after cleaning, tighten the screws, prevent oil, dirt jam tubing, open the energy pump to start working again. The press deflects and bends When the platen is moved to one side, the platen is not well guided during the feeding process, and the distance between the upper and lower axes is not parallel. Which side means there is too much free space. During adjustment, stop the machine first, take off the driving gear on both sides of the lifti

The components of the capsule filling machine The automatic capsule filling production line is generally composed of main driving system, electric control system, conveying system, feeding system and discharging part. In addition, 000#, 00#, 0#, 1#, 2#, 3#, 4# and 5# capsules can be produced by changing different types of molds. The whole machine has beautiful appearance, fine technology, simple operation and convenient use. The design integrates the filling seat and measuring plate into one, which improves the loading precision and extends the service life. Can automatically eliminate the residual capsule, the residual capsule recovery, reuse, improve the work efficiency, increase economic benefits. Vacuuming and weeding are designed inside the machine to facilitate the cleaning of the table. The filling rod nut is made of 304 stainless steel instead of plastic material to avoid nut breakage. With the development and technical progress of the capsule filling machine,

Hot pressing sealing of blister packing machine According to the analysis of the industry report, in the process of heat sealing packaging, the blow-cover type PVC tape aluminum foil is supplemented by the parallel coupling effect of the drum sealing coil and the coil mesh between each other, and the coil is under the action of certain pressure and temperature. Because the contact between the hot sealing roller and the anilox roller is linear, the pressure required is relatively small. In the process of heat sealing of aluminum-plastic blister packaging, the PVC tape is parallel and cross-connected with the plane of the aluminum heat sealing plate, in the same plane, under the action of certain temperature and pressure. The contact between the hot seal plate and the mesh plate is shallow and requires higher pressure. However, when the coil or hot plate seal, there are problems, the hot plate seal is not clear, the net line is not clear, with PVC sealed bubble cover, must be solved

Technological progress of tablet press High speed and high yield production. In order to meet the needs of intensive development of pharmaceutical factories, the original presses of 20,000-50,000 units per hour can no longer meet the demand of the market. As a result, in the past few years, there have been eight manufacturers of high-speed tablet presses. Recently, the market launched automatic high-speed tablet press, the output of 560,000 pieces/hour. Trends in standardization and serialization. The factory can standardize and systematize the production, the user can choose and purchase the equipment according to the standardization series, regardless of the specification, the parameter, the add-on standardization and the series mold. Versatility. The generality of the tablet press indicates the development level of the pharmaceutical machinery industry and the personalized needs of users. For example: a tablet press with a ring and two laminates; A tablet press capable of p

The market of capsule filling machine Automatic capsule filling is flexible, accurate filling dose, novel structure and easy to operate. It is an economical and practical medicine capsule filling equipment at present. Automation trend of the development of the capsule filling machine is an important mechanical automation technology leap, but the development of our time is short, short of technology to some aspects of the world average level, mechanical automation technology in the application of machinery industry, increased significantly, the development of mechanical automation road, capsule filling machine manufacturers need to trial and error, will improve technology perfect. It is known that in the national drug market, most of the capsule filling equipment has problems such as powder spraying, low filling accuracy, empty capsule, broken capsule and so on. These problems will not only affect the quality of products and the normal operation of equipment, but more important