Blister packing machine delivery Blister packaging machine is my company recently launched a new advanced equipment, suitable for all kinds of tablet, capsule pharmaceutical, chemical, light industry, food industry such as solid liquids aluminum-plastic blister packaging (aluminium), yesterday the delivery device is tailored for the customer the red insect blister packaging machine, our qc inspector before shipment carefully examined the rack installed with chassis, frame and plate, plate correction, cabinet installation, main shaft connection, box installed CAM, mesa of sheet metal and feeding roller, dragon framework installation, etc.​ In addition to the basic content, the factory inspector also make the corresponding inspection, confirm that the customer required voltage, screen content, electrical box, lines, nameplate, toolbox, mold, open the machine more than 4 hours before test, check the box body with and without oil, the trachea pipe with and without leakage gas leakage

Change the dosing plate and filling rod of the capsule filling machine 1. Loosen the fastening screw and lift the powder hopper with the help of spring spring; 2. Use a vacuum cleaner to remove the remaining powder in the ring; 3. Turn the main motor with the handle to make the punching rod seat disk in the highest position; 4. Loosen the cover nut and turn the knob clockwise to make the pressing plate and filling gripper rise and lift; 5. Remove the small pressing plate screw with long holes under the gripper and remove the filling rod. After replacing the filling rod, tighten the screws on the small pressing plate and wait for installation; 6. First, loosen the screws on the bar board and pull out the bar upward, unscrew the two fastening screws on both ends of the cover plate of the powder holding ring, rotate the main motor with the handle accordingly, loosen the four fastening screws that fix the powder holding ring, slowly lift the powder holding ring and the cover

Station introduction of aluminum-plastic blister packaging machine DPP-E aluminum-plastic automatic blister packaging machine is an improved equipment recently launched by our company. It adopts frequency conversion speed regulation and integrated control technology of machine, electricity, light and gas. It is carried out in strict accordance with the requirements of the pharmaceutical industry (GMP) standards Innovative design, leading in the country, this machine has advanced functions, simple operation and high output. It is the most ideal packaging equipment for large and medium-sized pharmaceutical companies, health care products and food industries. Main functions: PVC blister forming, automatic material filling, PTP aluminum foil flat pressing and heat sealing, image and text matching, batch number imprinting, pressing and tearing line, medicine plate punching, waste recycling.

The performance of blister packaging machine 1. The whole machine can be divided and packed into 1.5m elevator and divided purification workshop. Screws are used for consolidation and assembly is simple. 2. The mold adopts keyway positioning and pressing plate clamping. 3. With the photoelectric compensation mechanism, the printed aluminum foil can be graphic version. 4. The main motor adopts frequency conversion speed regulation: the blanking frequency can be from 20 to 40 times/min. The corresponding blanking frequency can be set according to the stroke length and the feeding difficulty of the filling material and other factors. 5. Manipulator clamping feeding mechanism, stable operation, accurate synchronization, arbitrary adjustment of travel within the established range, that is, the plate size can be designed at will within the range. 6. The forming heating plate automatically closes and opens, which can be started up delayed after the heating plate is put down, limit

Application scope of blister packaging machine Blow-cover packaging machine is suitable for aluminum, aluminum, paper, aluminum, aluminum and other materials of the packaging machine, using PLC computer control, man-machine interface operation, stepless frequency conversion speed regulation function, with a high degree of automation, advanced technology, complete functions, durable and other characteristics. The machine is widely used in various industries, such as medical treatment, liquid paste food, liquid paste supplies, cosmetics and skin care products, daily necessities, medicines and so on. 1. Drug packaging: hard capsule, soft capsule, tablet, pill, Danmi pill, Cordyceps sinensis tablet, sea cucumber, effervescent tablet, rubber pill, buccal tablet, ampoule, penicillin bottle, panax notoginseng powder, tablet, etc.; 2. Food packaging: milk slice, lollipop, fruit cake, bread, candy, Funny egg, donkey-hide gelatin, chocolate bean, skittles, bubble gum, scented tea, chewing

Seeding mechanism of semi-automatic capsule filling machine Semi-automatic hard capsule filling machine changes the output of the machine by changing the mold (changing the number of mold holes). When the machine is running, the capsules in the capsule hopper on the seeding station will enter into two feeding plates one by one through the small capsule funnel. There is a reed switch under the seeder. When the seeder tube is driven by the sector gear, it releases a row of capsules (1, 2, 3, 4, 5: 7 in a row, 0: 6 in a row, 00: 5 in a row, 000: in a row 5), when the seeding tube rises upward, the switch will immediately close the seeding tube. The capsule that has fallen under the capsule comb is pushed forward to the turning position by the pushing capsule plate, and the capsule head is pushed downward and turned around at the same time (body downward When the capsule is pressed downward from the correction block by the vertical fork, the capsule is sucked into the mold by the air

Disassembly and assembly of single punch tablet press 1.Plate of the intermediate mould Disassembly； draw out the fender and take away the hopper.Unscrew the fixed bolt of the hopper machine and the spring,unscrew the fixed bolt and spring gasket of the plate of intermediate mould,and then you can take away the plate of intermediate mould. Assembly:Refer to above contrary turn to go on.Attention correction to avoiding damage the orifice of the hopper when screw the fixed bolt of the hopper. 2.Uprush rod Disassembly:Unscrew the nuts and turn the uprush rods to separate it with follow-move shaft.Turn hand wheel to rasie the eccentric wheel shield to the top point;turn hand wheel to move it upper direction,and then you can dreaw the uprush rod out of the orifice of the mould.Assembly please refers to above instruction in counter sequence. 3.Downrush rod: Disassembled:Unscrew the fixed bolt of downrush,bolt and turn the gear press plate to adjust gear,lower the downrush rod and take

Technical process of blister packaging machine 1. PVC preheating Start the machine for heating. Close the upper and lower heating plates, and heat the PVC plastic sheet between the upper heating plate and the lower heating plate. After preheating, under the action of traction, it enters the blister forming mold. The upper molding die for blister molding is fixed, and the lower molding die rises to the upper limit under the action of the cam and presses the PVC plastic sheet hard. At this time, the air valve is opened, and the compressed air passing through the filter pressure reducing valve enters the cavity of the lower molding die through the upper molding die, and the PVC plastic sheet is formed by positive pressure. 2. Feed After forming the PVC plastic sheet into a certain shape, the feeder will transport the packaged material into the blister. Specially shaped materials are manually fed. It is equipped with a photo inspection system that can automatically remove debris from

Replacement of the dosing plate and the filling rod of the automatic capsule filling machine 1. Loosen the fastening screw to raise the powder hopper with spring force; 2. Use a vacuum cleaner to remove the remaining powder in the medicine pool ring; 3. Rotate the main motor with the handle to make the punch seat plate in the highest position; 4. Loosen and remove the cap nut, turn the knob clockwise to raise the pressure plate and the filling holder and lift it off; 5. Remove the small pressure plate screw with the long hole under the holder, and remove the filling rod. After replacing the filling rod, press on the small pressure plate and tighten the screws for installation; 6. First loosen the screws on the barrier plate and pull out the barrier plate upwards, unscrew the two fastening screws at both ends of the powder ring cover, rotate the main motor with the handle correspondingly, loosen the four fastening screws that fix the powder ring, and connect the powder ring to the

Precautions for packaging and packaging of blister packaging equipment 1. The inspector must check the whole machine for sheet metal inspection for obvious scratches, corners, burrs, and polished wires that have not been treated in place; 2. Confirm the electrical configuration of the equipment, confirm whether the voltage of the equipment is consistent with the order form, and check whether the electrical box and line trachea are clean; 3. Confirm whether the information on the nameplate is correct, whether the pasting mark is in the correct position, and confirm whether the tool box accessories and the mold are complete; 4. Test machine, whether there is abnormal noise and noise when the machine is running, confirm whether the various stations work normally during the machine operation, whether there is obvious swing, and whether the work is normal when the material is running, whether there is jamming (15-40 multi-speed operation) , Check whether the sample tested by the mold is