The function and characteristics of automatic blister packaging machine The automatic blister packaging machine is suitable for pharmaceutical and food blister packaging in pharmaceutical factories, health care products factories and food factories. The machine adopts PLC system control, touch screen panel operation, stepless frequency conversion speed regulation, and pneumatic joint control. It can complete aluminum-plastic, Blister packaging of aluminum-aluminum, paper-plastic products, easy to operate, suitable for packaging capsules, tablets, soft capsules, candy, medical equipment, jam, honey and other items. The machine features are as follows: It adopts servo motor traction, adjustable stroke, suitable for packaging of different size plates. The position of forming, heat sealing, batch number and punching can be adjusted arbitrarily, and debugging is simple and convenient. Automatic blanking, molds and automatic feeders can be designed according to customers' different mater

Installation and wire connection of semi-automatic capsule filling machine 1. Ground requirements The rack should be installed on the ground with a sufficient rated level. If it is installed on the floor upstairs, ensure that the support is not less than 1000 kg/m, with a rubber cushion at the bottom, and the level is the same as the level of the machine table of the ordinary school. 2. Vacuum oil Any vacuum pump sent at random is not lubricated, and the oil-free vacuum pump may run for a short time (less than 10 minutes). Before production, be sure to raise one liter of #100 special vacuum pump oil. After 1500 hours of use, the vacuum pump oil should be replaced, otherwise the damage will not be free of warranty. 3. Air demand Vacuum: The vacuum pump is connected to the vacuum cylinder, the inner diameter is 25mm, the wire end of the hose is connected to the vacuum cylinder, and the other side is connected to the vacuum nozzle of the machine. Air compressor: Turn on the air

​Precautions for installation of automatic blister packaging machine 1. Do not fix the small blister packaging machine on the ground because there are rubber wheels at the bottom of the machineto move. 2. Train professionals to operate and maintain the machine. 3. Connect the ground wire according to the keyhole. 4. The machine should be kept clean. 5. Lubricating oil should be added to all parts of the machine. 6. Lubricating oil should be added to the wheel box before production. 7. Use oil-free air compressor. 8. The pressure of forming station, heat-sealing station and stamping parts should be controlled within a certain range, otherwise it will affect the service life of the machine.

Recovery of powder from the capsule filling machine The machine adopts double pipeline device for dust absorption and powder recovery. One of the pipelines of the device is used for cleaning mold holes, absorbing residual capsules of the cap body not separated and cleaning the table surface. The other pipeline is dedicated to the recovery of the filling part of the powder, and is also equipped with a powder recovery device in the air flow adsorption pipeline. The collector consists of a body, a powder recovery filter and a powder bucket. The pipeline can effectively and directly recover the lost materials in the filling part. During the filling process of the filling machine, the materials lost in the filling part enter into the powder collector through the special powder recovery pipeline due to the suction of the dust collector. Under the action of the powder recovery filter cartridge, 85-95% of the powder is deposited in the powder holding barrel. And the gas through the body ca

Maintenance of automatic capsule filling machine Maintenance of automatic capsule filling machine In addition to the maintenance and cleaning of semi-automatic capsule filling machine, there are several maintenance work as follows: 1. Check the oil content of the main drive reducer every 200 hours, and add oil in time if there is any shortage, and replace the lubricant every 3,000 hours or half a year (the limit is for those who reach it first); (Its lubricating oil viscosity is 460~680 industrial closed extreme pressure gear oil, the original lubricating oil is "Shell" Shell Omala 220, it is recommended to use the same grade as far as possible) 2. The fuel content of the feed reducer shall be checked every 200 hours during operation, and the oil shall be replenished in time if it is found to be insufficient, and the oil shall be replaced every 1000 hours or four months (if it reaches the limit first); (Its lubricating oil is synthetic worm and worm oil with viscosity of 55

Warranty for blister packing machine 1.The machine warranty period is 12 months. 2. During the warranty period, the problem appeared in accordance with normal use and service instructions, we provide free fixing. 3. During the warranty period, such as one of the following conditions occur, it will be charged： （1）Can not provide a valid warranty card or purchasing documents. （2）Misuse and damage caused by improper repairs. （3）Transporting or damage caused by fall. （4）Failure and other damage caused by force majeure. （5）Use the power voltage caused damage other than those specified. 4. The appearance of the product, the vulnerability of consumables and accessories are not covered by the warranty. The accessories included Spring, Water Tank，Filter，Rubber Gasket and tooling in the tooling box. 5. Only for the above guarantee, does not make any express or other guarantee, either in the contract, on tort or otherwise, the Company liable for any special, incidental or consequential da

General failure of manual capsule filling machine The general faults of the semi-automatic capsule filling machine are the lack of capsules, the low rate of finished products in the mold hole of capsules, the flying cap during the separation of capsules, the failure of normal separation of capsules, the occurrence of skin brushing, concave opening and the failure of locking in place. Reasons for capsule failure: Defective capsules block the inlet of the capsule feeding plate, the capsule switch is too large or too small, and the capsule is damaged or in an uneven position. Method of elimination: remove the capsule with capsule needle, clean it out of capsule tank, adjust the position of capsule feeding switch, change the capsule tablet, or correct the Angle evenly. The reason of low yield of the capsule into the mold hole is that the horizontal fork is too far ahead or the empress dowager adjusts the position of the horizontal fork. Elimination method: Adjust the ho

Aluminum foil blister packaging machine blister forming The poor forming of aluminum foil bubble cover of blister packaging machine is generally divided into three types: insufficient or inconsistent depth of forming bubble cover, bubble eye rupture after forming, and above wrinkling after forming. 1. Reasons for insufficient or inconsistent depth of forming bubble cover: the forming depth is not adjusted properly. Solution: loosen the adjusting nut and adjust downward. Use vernier caliper to measure the depth of the forming bubble cover, which is 0.3-0.5mm deeper than the drug thickness. If the depth is inconsistent, use vernier caliper inner claw to measure the distance between the upper die bottom plate and the forming lower die in the forming station. 2. Reasons for bubble hole rupture after forming: the forming depth is too deep, and the elongation of aluminum foil is insufficient. Solution: reduce the forming depth, aluminum foil for another purchase. 3. Upper wrinkle after

Adjust the dispensing tray and sealing ring of the capsule filling machine The clearance between dosing disk and sealing ring should be preferably 0.03~0.08 mm. With larger particles, the clearance may be adjusted wider. Too narrow clearance may increase the resistance between dosing disk and sealing ring. Should too much powder leakage or resistance occur in the operation, adjustment of the clearance shall be made. Toadjust the clearance, draw out baffle and loosen fastening screw on adjusting base, first rotate adjusting knob counterclockwise to lower sealing ring, then rotate adjusting knob clockwise to raise sealing ring. After deciding the clearance between sealing ring and dosing disk with feeler gauge, lock the fastening screw. If sealing ring is adjusted too high, just rotate the adjusting knob counterclockwise to lower sealing ring and then rotate clockwise to raise it. Adjust from high to low shall not be allowed. The knob has a scale. Whenever you rotate one degree, sealing

Failure of plastic bubble forming of blister packaging machine The plastic foam forming fault of the blister packaging machine usually has the bottom film perforation of the blister and the forming is incomplete. 1. Reasons for blister bottom film perforation: the forming temperature is too high, and the PVC quality is poor. Solution: lower the temperature, replace PVC plastic sheet. 2. Incomplete forming: the forming temperature is too low, the upper and lower dies are not parallel, the O-type sealing ring is damaged, the blowing holes and exhaust holes are blocked, the air pressure is not suitable, and the blowing time is wrong. Solution: raise the temperature, adjust column ball nut (including locking nut), make the upper and lower die parallel fit when the seal is good, replace O-type sealing ring, dreg vent with steel needle, adjust the pressure of reducing valve, generally be (0.3-0.5mpa), adjust the blowing CAM position (wait for forming die to close line blowing).