Blister packaging process The cavity of the blister pack is large or small, and its shape is different due to the shape of the packaged goods. There are some that are available and some that are not. And the type of blister packing machine is also more. Nevertheless, the basic principle of blister packaging is roughly the same, and its typical process is: sheet heating → film forming → filling product → placing substrate → heat sealing → trimming and trimming. The above process can be completed by manual operation, semi-automatic operation and automatic operation. 1. Manual operation. Plastic sheet blister pre-forming, substrate pre-printing drama and cutting; When packing, manually put the product into the bubble cap, cover the substrate, and then seal the bubble cap and the substrate together with a heat sealing clamor. Some products on the circulation environment temperature and humidity requirements are not high, can not be heat sealing, and stapler stapling. 2. Semi-autom

Problems and solutions of capsule filling machine 1. The capsule is not falling smoothly in the capsule slide, and the outer diameter of individual capsules is too large or blocked by foreign bodies Replace qualified capsules Remove the foreign body with a tool The discharge capsule cannot enter the hole of the capsule plate The opening and closing time of the capsular spring is improper, and the position of the pushing claw and the pressing claw is improper 2. Poor separation of capsule body and cap There is a foreign body on the surface of the air separator The bottom top rod position is improper, the upper and lower bursa plate dislocation. There is a foreign body in the hole of the capsule plate 3. The vacuum tube is not tightly sealed or the vacuum degree cannot meet the requirements Eliminate waste capsules and remove foreign bodies Adjust the position of the jacking rod and tighten the position of the capsule plate Clean filter, check vacuum s

Problems and methods of using tablet press Drug crushing fineness is not enough, fibrous or elastic drug or oil composition content is more and mixed uneven. Solution: the drug can be crushed through the 100 mesh screen, the selection of strong adhesive, appropriate increase the pressure of the tablet press, increase the oil drug absorbent fully mixed methods to overcome. Insufficient amount of adhesive or wetting agent or improper selection, so that the texture of the particles loose or uneven distribution of particle size, coarse and fine grain stratification. Solution: choose the appropriate adhesive or increase the dosage, improve the granulation process, mixing more soft materials, mixing particles and other methods to overcome. The water content of the particles is too little, and the excessively dry particles have greater elasticity. The drugs containing crystal water lose more crystal water in the drying process of the particles, which makes the particles brittle

Safe operation of blister packing machine Aluminum packaging machine is almost the necessary machinery for any enterprise, but many enterprises have had accidents, property losses fall next, mainly this equipment is easy to cause physical injury to workers, common burns and cuts. Scalds mainly occur in PVC thermal forming station, heat sealing and pressing station, especially in heat sealing and pressing station. Due to the large difference in the shape and size of materials in domestic equipment, the proportion of falling into the bubble cap is low, and the bubble cap needs to be manually filled or picked up, which is easy to cause hand burns. It is suggested that the workers should pay attention to these two stations. The manufacturer has posted warning signs on the stations that are easy to burn. The cutting mainly occurs in the cutting station. This station or up and down cutting, or left and right cutting, according to the installation of the cutter. Cutters used for a pe

Lubrication for components of rotary tablet press 1. The general lubrication of the machine parts are equipped with oil cups and nozzles on the surface of the machine parts. Butter and oil can be filled respectively according to the type of oil cups. 2. The glass oil cup on the top cover is lubricated with the turntable and bearings, which are in operation at a rate of 2-4 drops per minute. 3. the screw cap oil cup on the worm is to lubricate the worm gear, in operation according to the actual lubrication and. 4. Both ends of the drive shaft are equipped with rolling bearings, and the oil nozzle is installed outside the shaft shell. It can be refueled once every two weeks and pressed into the oil gun. 5. The tail of the punch rod and the curve rail are lubricated with butter. It should not be too much to prevent the oil from infiltrating into the powder and affecting the quality of the tablet. 6. when refueling should pay attention not to make the oil spill out of the

The mechanical part of the stretch film vacuum packing machine 1. The main body of the equipment is made of SUS304 stainless steel, alloy aluminum and ultra-high molecular engineering materials. The ingenious design improves the strength, corrosion resistance, acid and alkali resistance and stability of the main body of the equipment. 2. The mould is made of 6061 alloy aluminum once, and the German technology is introduced. To avoid the occurrence of faults such as porosity cracking of casting aluminum mold products, 3. The molding studio and heat sealing studio are made of 6061 alloy aluminum as a whole to ensure that there is no air leakage and waste of heat energy caused by sealing problems when the working room is used for a long time. 4, servo control system and electrical box separate device, to ensure that due to current and other factors to make signal interference and static electricity and other phenomena, affect the production and cause inconvenience in operation

Control system of stretch film vacuum packing machine 1, Germany Siemens PLC control. 2, Germany Siemens man-machine interface touch screen, control screen push-pull design, simple and convenient operation. 3, Germany Siemens servo system control, high speed and high precision, to ensure that the molding and heat sealing effect in the production process is beautiful, at the same time to ensure that each step is stable and accurate. 4, Adopts Regina chain imported from Italy, Nulide cylinder and SMC solenoid valve to ensure the precise coordination of machinery. 5, Siemens series low-voltage electrical appliances, with perfect safety protection measures, so that the equipment can work continuously, improve the stability of electrical appliances and service life cycle. 6, electrical appliances and servo installation separately, equipment work without signal interference, to ensure the normal operation of the equipment.

The main function of stretch film vacuum packing machine 1, Packaging machine can do single-side stretch molding, double-side stretch molding, double-side cursor positioning stretch molding, hard film stretch molding, close stretch packaging, improve production efficiency, improve product packaging appearance grade, reduce packaging cost and labor cost, save energy cost. 2, Double-sided molding, can achieve double-sided photoelectric eye positioning, cutting corners, with easy to tear, play hanging hole and other functions. 3, according to different customer product packaging needs, customized special mold production, at the same time one machine can produce a variety of products. 4, On the basis of vacuum packaging, the equipment can realize the functions of adjustable gas packaging (filling mixed gas and nitrogen), etc. 5, equipment with solid and liquid mixed packaging. 6, the equipment can achieve date printing or inkjet coding.

Stretch film vacuum packaging machine technology 1. The lifting mechanism of the packaging machine is introduced from Germany with four connecting rod bending knee lifting technology. The lifting speed is uniform, stable and balanced, and the failure rate is very low to improve the quality stability in the production process of the equipment. 2. Pneumatic control system; Advanced pneumatic drive components, improve equipment wear problems, prolong the service life of the equipment, sensitive response, reduce the overall maintenance and operation costs of the equipment, improve work efficiency. 3. Automation, intelligence and energy saving: summarize and analyze the demands of various domestic food industries, and improve the packaging cost, labor cost and electricity cost. Easy to operate and easy to understand, fast speed, low energy consumption, far ahead of the domestic industry level. 4, one equipment can use a variety of molds and asynchronous film, that is, can do a v

Stretch film vacuum packing machine 1. When people are using the stretch film machine, if the heat sealing temperature is high, it will lead to too much heat in the film, and then there is a wrinkling phenomenon. At this time, we can reduce the heat sealing temperature and reduce the heat in the film to solve the problem. 2, when the machinery and equipment to stop using the membrane within the heat sealing plate stay for a long time, can also lead to membrane by too much heat, shrink film showed when use, should be to ensure that the film has been running in the process of production, reduce the number of key, can effectively avoid the film heat and contraction deformation problems more, Causes the film to appear in the use process has the wrinkle phenomenon. 3. We are a professional manufacturer of vacuum packing machine. The stretch film vacuum packing machine produced by our company can be equipped with automatic coding system according to the packaging requirements of use