Operation procedure of bubble cap machine 1. The green indicator light is on, and the two heating switches, upper and lower forming and hot sealing, open the operation position respectively. The temperature controller controls the forming temperature, which is generally preset at 100℃C, and the second temperature controller controls the heat seal. The temperature is preset at 130℃C~140℃C. Upper and lower forming and heat sealing temperature controller preset temperature; Subject to specific discretion. 2. Put down the pressing block on the primer roller, and the temperature of the forming heating plate is in place, then open the host machine. Plastic PVC is formed first, and the forming bubble eye is in line with the hole position of the heat sealing mold. Observation of plastic (refers to the machine board surface has become a new PVC) walking whether the left and right deviation. If there is a bias should adjust the starting pressure roller seat to adjust the direction of the l

The scope of use of blister packing machine 1, the use of new domestic high-power transmission mechanism, driven by the chain drive shaft, avoid the error and noise of other gear transmission. 2, The electrical appliance adopts the imported control system, can be configured according to customer requirements, the lack of material leakage and lack of grain detection and elimination device (Omron sensor). Adopt imported frequency conversion governor. 3, The whole machine adopts segmented combination: PVC forming, feeding, hot sealing for a section, tropical aluminum cold forming, hot sealing, punching for a section can be separated packaging. 4, The use of photoelectric control​ system, PC, PTP, tropical aluminum packaging automatic feeding, automatic waste side receiving device, to ensure the long distance and multi-station synchronous stability. 5, can be equipped with photoelectric detection and correction device, with imported stepping motor traction, image and text plate printi

Work content of blister packing machine 1. Turn on the main power switch, connect the compressed air and the cooling water. 2. Turn on the "heating" switch, and the host starts to heat. 3. check the batch number is correct, if the army will change the batch number. 4. When the heating temperature reaches the set value, press the "dot action" button to open the lower die. 5. Lift up the heating plate, open the "step clamping" button, pass the PVC through the molding mold and the clamping cylinder, and wear the PVC outside the body. 6. Put down the heating plate, press the "Start" button, adjust the rotation of the "host speed regulation", make the host run at a low speed. After the PVC is formed, go out about 3 meters, press the "stop" button to stop the host. 7. Obact the forming condition of the bubble cap, whether it is uniform and straight, and whether it is bent on the length of 3 meters. 8. Cut the end of the PVC with scissors, turn it 180 degrees and put the PVC into the

Mold change and synchronous conditioning of flat blister packing machine (1) Replacement of molds: When the packaging form changes, that is, the quantity, size, variety and specification of packaging plate change, the molds and corresponding parts need to be replaced. The general steps for changing the mold and the corresponding parts are as follows: turn off the heating switch, cut off the water and air supply, and turn all the switch knobs to the "0" position; Remove the molding mold and covering film, and use the point button to make each station open to the maximum value; Remove the parts that need to be replaced, and replace them when the device is cooled to room temperature. After the replacement, make synchronous adjustment. After that, press the button to make the machine run for a short time, check the reciprocating movement, and require smooth operation and no impact. (2) the replacement of parts and components: (1) when the type and quantity of the packaging change, an

Blister packaging molding According to the principle that P V C film (hard sheet) is heated through the mold and is formed into the desired shape and size by compressed air or vacuum, the following aspects should be solved when there are problems in the formed bubble caps (1) Whether P V C film (hard film) is qualified product; (2) whether the temperature of the heating device is too high or too low; (3) whether the surface of the heating device is adhering to P, V and C; (4) whether the forming mold is qualified, whether the forming hole is smooth and whether the pores are unobstructed; (5) Whether the cooling system of the molding mold works normally and effectively; (6) the vacuum degree and exhaust rate of the roller negative pressure forming can reach the normal value, and the pipeline has no abnormal loss; (7) whether the compressed air formed by plate positive pressure is clean and dry, whether the pressure and flow can reach the normal value, and whether the pipeline ha

Features of stretch film packing machine Stretch film vacuum packing machine has the following characteristics: 1. Wide applicability. Can pack solid, liquid, fragile and hard and soft materials, pallet packaging, blister packaging, packaging, soft film vacuum, hard film inflatable packaging. 2. High efficiency, saving labor cost, low packaging cost. All packaging except the filling area (some irregular goods) are completed by the machine. Loading can be done manually or mechanically. Some models can pack at a rate of more than 12 cycles per minute. 3. Compliance with hygiene. When mechanical loading is selected, one person is required to operate the equipment control panel (start up or set the program) in the whole packaging process, and no other manual operation is required. From bag/box production to packaging in one go, reduce transitional pollution. If choose the packing material that can be resistant to high temperature, high temperature sterilization still can be processed a

Requirements for different foods on stretch film packing machine 1, the requirements of different food air conditioning fresh-keeping in the application of food air conditioning packaging technology, according to the different storage characteristics of the product to choose the appropriate atmosphere. 2, oxygen sensitive food (such as fried peanuts, etc.) packaging atmosphere, vacuum after filling nitrogen can further reduce the residual oxygen content in the package, that is, nitrogen packing, better than vacuum packaging effect. 3, red fresh meat packaging atmosphere, using high oxygen content and carbon dioxide mixture of gas, can keep the color and corrosion. 4, fresh fish packaging atmosphere, the use of O2, CO2 and N2 mixture of gas, can simultaneously inhibit the reproduction of aerobic bacteria and anaerobic bacteria and preservation. 5, fresh fruit and vegetable packaging atmosphere, the use of low oxygen, high carbon dioxide (compared with air) and nitrogen mixture of g

Blister packaging technology Blister packaging, also known as Blister Packaging Eye, or PTP (Press ThroughPackaging) packaging technology, is one of the rapidly developing forms of drug packaging in recent years. PTP technology to heat and soften the plastic film and placed in the mold, or blow compressed air through a vacuum pump, so as to form blister medicine eyes, and then coated with glue aluminum foil medicinal under certain temperature and pressure conditions sealed to form a blister packaging. At present, pharmaceutical blister packaging has become the mainstream of tablet, capsule, pill and other solid dosage form packaging, the development momentum will continue. Blister packaging in our country the status quo of drug along with our country reform and opening-up and the deepening of the medical and health system reform, especially after China's entry into the WTO, the international pharmaceutical companies greater access to China, China's pharmaceutical industry competition,

Stretch film packaging machine maintenance Automatic stretch film vacuum packaging machine packaging goods, rapid, efficient, accurate, saving, strong adaptability, can pack a variety of items, is our daily packaging production in the most common one of the machinery. The maintenance of the equipment is very important. The improper maintenance causes the service life of the automatic stretch vacuum packing machine to be too low. The following are the maintenance rules of the automatic stretch vacuum packing machine shared with us. Number one, periodically add oil. Because the long time of operation will cause the internal machine to run in improper, internal does not conform to the appropriate point of lubricating oil can help to operate very well. It is recommended to increase every 80 days. Second, security. The standard pressure of automatic stretch vacuum packing machine is 0.3Mpa, which should not be adjusted too much or too little. Otherwise, it will paralyze the machine. And

The operation content of blister packing machine 1. The machine is fully enclosed, and the parts that contact with the drug are made of high quality stainless steel plate, which is smooth, smooth and without edges and corners. The equipment itself does not pollute the production environment, and does not pollute the drugs, and conforms to the GMP standard. 2.PVC molding is plate-type positive pressure molding, which is composed of forming die and blowing die. The forming mold moves downward, and then moves downward 0.5 ~ 1mm after contacting the blowing mold. The air pressure is 0.35 ~ 0.5Mpa. When the forming mold moves upward 0.5mm, the blowing stops, and the forming is completed. 3. The clamping step adopts the swivel arm type double clamping mechanism, two pairs of fixed clamping does not move, a pair of reciprocating movement clamping PVC is sent into. Adjust the length of the swing rod and connecting rod, so that the stepping distance can meet the requirements of the plate siz