Hot pressure sealing of bubble cap machine In the hot sealing process of the drum type aluminum foam cap packaging, the P, V, C belt and aluminum foil are completed by the meshing rolling of the parallel roller heat sealing roller and the anilac roller under the action of certain temperature and pressure. The contact between the heat sealing roller and the anilox roller is linear and the pressure required is relatively small. In the process of hot pressing sealing of flat plate aluminum blister packaging, P, V, C strip and aluminum foil are hot pressing sealed by parallel flat plate and mesh plate in the same plane under certain temperature and pressure. The contact between the heat sealing plate and the mesh plate is planar contact, and the pressure required is relatively large. Whether it is drum type or plate type hot sealing, when the heat sealing mesh is not clear, the depth of mesh is different, the P, V and C belt out of position during thermal sealing caused blisters and oth

Blister packing machine packaging requirements China's laws have made more and more strict restrictions on product packaging, and put forward higher requirements on packaging labeling and printing. In the industry standard of pharmaceutical blister packaging machine, the packaging machine must have a batch number device. Packing machine printing generally adopts punch molding method to print out the production date and batch number. Batch number can be made in separate station, can also be with heat sealing, indentation in the same station. Indentation A piece of aluminum-plastic packaging medicine may be suitable for multiple use, for ease of use, can be pressed on a piece of easily cracked broken marks, the piece can be easily broken into a number of small pieces by hand, each small piece for a single dose. Blanking will be sealed after the ribbon packaging finished products blanking into the specified size (that is, the size of a piece) known as the blanking process. In order to

Operation procedure of bubble cap machine 1. The green indicator light is on, and the two heating switches, upper and lower forming and hot sealing, open the operation position respectively. The temperature controller controls the forming temperature, which is generally preset at 100℃C, and the second temperature controller controls the heat seal. The temperature is preset at 130℃C~140℃C. Upper and lower forming and heat sealing temperature controller preset temperature; Subject to specific discretion. 2. Put down the pressing block on the primer roller, and the temperature of the forming heating plate is in place, then open the host machine. Plastic PVC is formed first, and the forming bubble eye is in line with the hole position of the heat sealing mold. Observation of plastic (refers to the machine board surface has become a new PVC) walking whether the left and right deviation. If there is a bias should adjust the starting pressure roller seat to adjust the direction of the l

The scope of use of blister packing machine 1, the use of new domestic high-power transmission mechanism, driven by the chain drive shaft, avoid the error and noise of other gear transmission. 2, The electrical appliance adopts the imported control system, can be configured according to customer requirements, the lack of material leakage and lack of grain detection and elimination device (Omron sensor). Adopt imported frequency conversion governor. 3, The whole machine adopts segmented combination: PVC forming, feeding, hot sealing for a section, tropical aluminum cold forming, hot sealing, punching for a section can be separated packaging. 4, The use of photoelectric control​ system, PC, PTP, tropical aluminum packaging automatic feeding, automatic waste side receiving device, to ensure the long distance and multi-station synchronous stability. 5, can be equipped with photoelectric detection and correction device, with imported stepping motor traction, image and text plate printi

Work content of blister packing machine 1. Turn on the main power switch, connect the compressed air and the cooling water. 2. Turn on the "heating" switch, and the host starts to heat. 3. check the batch number is correct, if the army will change the batch number. 4. When the heating temperature reaches the set value, press the "dot action" button to open the lower die. 5. Lift up the heating plate, open the "step clamping" button, pass the PVC through the molding mold and the clamping cylinder, and wear the PVC outside the body. 6. Put down the heating plate, press the "Start" button, adjust the rotation of the "host speed regulation", make the host run at a low speed. After the PVC is formed, go out about 3 meters, press the "stop" button to stop the host. 7. Obact the forming condition of the bubble cap, whether it is uniform and straight, and whether it is bent on the length of 3 meters. 8. Cut the end of the PVC with scissors, turn it 180 degrees and put the PVC into the

Mold change and synchronous conditioning of flat blister packing machine (1) Replacement of molds: When the packaging form changes, that is, the quantity, size, variety and specification of packaging plate change, the molds and corresponding parts need to be replaced. The general steps for changing the mold and the corresponding parts are as follows: turn off the heating switch, cut off the water and air supply, and turn all the switch knobs to the "0" position; Remove the molding mold and covering film, and use the point button to make each station open to the maximum value; Remove the parts that need to be replaced, and replace them when the device is cooled to room temperature. After the replacement, make synchronous adjustment. After that, press the button to make the machine run for a short time, check the reciprocating movement, and require smooth operation and no impact. (2) the replacement of parts and components: (1) when the type and quantity of the packaging change, an

Blister packaging molding According to the principle that P V C film (hard sheet) is heated through the mold and is formed into the desired shape and size by compressed air or vacuum, the following aspects should be solved when there are problems in the formed bubble caps (1) Whether P V C film (hard film) is qualified product; (2) whether the temperature of the heating device is too high or too low; (3) whether the surface of the heating device is adhering to P, V and C; (4) whether the forming mold is qualified, whether the forming hole is smooth and whether the pores are unobstructed; (5) Whether the cooling system of the molding mold works normally and effectively; (6) the vacuum degree and exhaust rate of the roller negative pressure forming can reach the normal value, and the pipeline has no abnormal loss; (7) whether the compressed air formed by plate positive pressure is clean and dry, whether the pressure and flow can reach the normal value, and whether the pipeline ha

Features of stretch film packing machine Stretch film vacuum packing machine has the following characteristics: 1. Wide applicability. Can pack solid, liquid, fragile and hard and soft materials, pallet packaging, blister packaging, packaging, soft film vacuum, hard film inflatable packaging. 2. High efficiency, saving labor cost, low packaging cost. All packaging except the filling area (some irregular goods) are completed by the machine. Loading can be done manually or mechanically. Some models can pack at a rate of more than 12 cycles per minute. 3. Compliance with hygiene. When mechanical loading is selected, one person is required to operate the equipment control panel (start up or set the program) in the whole packaging process, and no other manual operation is required. From bag/box production to packaging in one go, reduce transitional pollution. If choose the packing material that can be resistant to high temperature, high temperature sterilization still can be processed a

Requirements for different foods on stretch film packing machine 1, the requirements of different food air conditioning fresh-keeping in the application of food air conditioning packaging technology, according to the different storage characteristics of the product to choose the appropriate atmosphere. 2, oxygen sensitive food (such as fried peanuts, etc.) packaging atmosphere, vacuum after filling nitrogen can further reduce the residual oxygen content in the package, that is, nitrogen packing, better than vacuum packaging effect. 3, red fresh meat packaging atmosphere, using high oxygen content and carbon dioxide mixture of gas, can keep the color and corrosion. 4, fresh fish packaging atmosphere, the use of O2, CO2 and N2 mixture of gas, can simultaneously inhibit the reproduction of aerobic bacteria and anaerobic bacteria and preservation. 5, fresh fruit and vegetable packaging atmosphere, the use of low oxygen, high carbon dioxide (compared with air) and nitrogen mixture of g

Blister packaging technology Blister packaging, also known as Blister Packaging Eye, or PTP (Press ThroughPackaging) packaging technology, is one of the rapidly developing forms of drug packaging in recent years. PTP technology to heat and soften the plastic film and placed in the mold, or blow compressed air through a vacuum pump, so as to form blister medicine eyes, and then coated with glue aluminum foil medicinal under certain temperature and pressure conditions sealed to form a blister packaging. At present, pharmaceutical blister packaging has become the mainstream of tablet, capsule, pill and other solid dosage form packaging, the development momentum will continue. Blister packaging in our country the status quo of drug along with our country reform and opening-up and the deepening of the medical and health system reform, especially after China's entry into the WTO, the international pharmaceutical companies greater access to China, China's pharmaceutical industry competition,