The market of capsule filling machine Automatic capsule filling is flexible, accurate filling dose, novel structure and easy to operate. It is an economical and practical medicine capsule filling equipment at present. Automation trend of the development of the capsule filling machine is an important mechanical automation technology leap, but the development of our time is short, short of technology to some aspects of the world average level, mechanical automation technology in the application of machinery industry, increased significantly, the development of mechanical automation road, capsule filling machine manufacturers need to trial and error, will improve technology perfect. It is known that in the national drug market, most of the capsule filling equipment has problems such as powder spraying, low filling accuracy, empty capsule, broken capsule and so on. These problems will not only affect the quality of products and the normal operation of equipment, but more important

Check the capsule filling machine before starting Make sure the power switch is normal, the power line is not damaged, no falling off or falling off, and the grounding of the pen detection equipment is good. Check whether the polisher, vacuum cleaner and loading device are in good condition and have been cleaned. Check whether the mold is installed correctly, check concentricity and parallelism, the mold is matched well and has been cleaned. Check whether the water level and water quality of vacuum pump storage tank are normal. Check whether the indicators are within the normal range. Check whether the filling machine surface is clean and tidy, check whether the electrical control panel and other items are left behind. Check whether there is enough grease in the oil pump and each part to prevent machine damage. After all the above inspections are normal, the equipment can be replaced with the normal logo and ready to start up.

Feeding for the capsule filling machine In the pharmaceutical field, the drugs in capsules are mostly powder or particles that stimulate the esophageal and gastric mucosa, or have bad taste, which are volatile, easily broken down by oral saliva, and easily inhaled by the trachea. These drugs are packaged in capsules to protect the drug as well as the digestive organs and respiratory tract from damage. Removing the capsule can lead to drug loss, drug waste, and reduced efficacy. In addition, some drugs need to be dissolved and absorbed by the gut, and the capsules can protect the drug from being destroyed by stomach acid. At present most of the capsule filling machine filling powder, existing capsule filling machine feeder is usually at the top of the capsule filling machine, need workers to get a bag of a bag of finished product capsule is placed on the top of the capsule filling machine, and then pour into the feeder, in general, about two meters tall machine need to use the lad

Other factors affecting the capsule filling machine Other factors affecting the capsule filling machine generally include environment and transportation. The environment A fully enclosed environment is mainly reflected in temperature and humidity. The ideal relative humidity condition is 35-65%, and the temperature is 15-25℃. Too low humidity will make the shell brittle and easy to decompose. A capsule with high humidity will become sticky and deformed. Too high a temperature will cause thermal damage to the capsule. The transportation In the process of transportation, if the hollow capsule is impacted, the deformation of the capsule may hinder the filling of the capsule in the production process, affecting the production efficiency and product quality. To ensure the quality of the capsule products, the first to ensure that the production conditions meet the requirements, reasonable transportation. Now, with the continuous improvement of filling technology, the degree of automati

How to solve the capsule filling powder too sticky When the capsule filling machine is working, if the working powder is too viscous, it can be generally improved from the following points: 1. If the hygroscopicity of the powder causes the powder to be too sticky, the hygroscopicity should be reduced as far as possible, and the effective extraction process should be carried out to retain the part of the powder containing more starch, or some auxiliary materials should be added to reduce the hygroscopicity. 2. Keep the powder as dry as possible, less water is better. 3. Reduce the humidity and temperature in the workshop. 4.The packing of the powder must be close and effective against dampness and moisture. 5. Keep the powder as fine and even as possible. 6. The filling rod of the machine should be checked and replaced in time if there is any wear. 7. Add auxiliary materials to increase the fluidity and lubricity of the powder.

Factors influencing the accuracy of capsule filling machine The operator did not add powder as required in the manual before starting. Before operation, the powder is respectively loaded into the hopper and sent to the measuring room through the feeder. The measuring chamber should contain more than half of the powder before filling. The operator did not replenish the materials in time during the operation, which directly affected the filling state of the drugs in the measurement model, leading to the difference in the quantity. The fluidity and viscosity of drugs are the main factors affecting the measurement accuracy. Due to the lack of fluidity of the drug, the powder viscosity is high, the filling volume is difficult to control, and the connection between the measuring plate and the copper ring may also occur. The drug is not uniform, the particle size difference is big, the particle is thin and thick, fluidity is poor. In order to solve the problem of drug fluidity, it is nece

Maintenance of capsule filling machine 1. When the machine runs normally for a long time, when a batch of drugs is changed or shut down for a long time, the parts in direct contact with the drugs should be cleaned regularly. 2. The transmission mechanism under the working platform of the machine tool should be constantly added with appropriate lubricant to reduce the wear of parts. 3. The main transmission reducer should be checked once a month to see if the oil is insufficient, and it should be replenished timely. The oil should be changed every 6 months; Change the oil every 3000 hours. Oil should be used as a rule of thumb. 4.Safety protection clutch, normal load overload clutch does not slip, but due to long-term use may appear slip phenomenon, when the clutch sliding phenomenon, may be the screw nut to tighten, to ensure the normal operation of the machine. 5. The vacuum system of the vacuum separator in the filling capsule is mainly used to put the cover on the body after

Liquid capsule filling A full automatic liquid hard capsule filling machine, liquid can be loaded in the hard capsule or low or medium viscosity of the material, its characteristic is: a lot in the first run orbital module and the corresponding module, including orbit a node contains a module mounting holes nano capsule, capsule in orbit has a hole, put the hat and cap, the cap body distribution holes are arranged in a module, the first module of the first orbit, and the second track is on the front end, but the second track to match with the first orbital. The utility model relates to a capsule feeding device, which is used for regularly feeding empty capsules in the upper module capsule hole in front of the first orbit; There is at least one capsule separation device for connecting the capsule hole of the lower module, separating the empty capsule from the capsule cap and capsule body, and connecting the capsule body with the capsule hole of the lower module; The utility model

Solution for unstable filling of capsule filling machine The filling instability of the capsule filling machine is generally analyzed as follows: 1. If it is the viscosity caused by hygroscopic Chinese medicine, the key process must also pay attention to the extraction, remove the alcohol and make appropriate improvement process to reduce the hygroscopic of raw materials (of course, the unrelated part). At the same time, keep part of the medicine contains starch while eliminating the increase. Of course, acrylic resins and other treatments can also be added to reduce moisture absorption. 2. If the exudate is the problem, it is basically suggested to adjust the formula to add microcrystalline fibers or to help the pharmaceutical exudate to adsorb dust or increase, for example, to alter sucrose in lactose, mannitol to reduce hygroscopic properties. 3. Add flow AIDS, such as silica gel, magnesium oxide, magnesium stearate, etc. 4. Powder should be as dry as possible with as little hu

Customers to the company to investigate the capsule filling machine With the continuous development of the company and the continuous innovation of technology, Hanyang technology is also constantly expanding the domestic and international market. On September 7, 2020, customers came to visit our company. Accompanied by Mr. Xing and technical personnel, the customer visited the workshop and equipment of the company, and communicated in detail the strength, product situation and sales situation of the company. The customer has strict requirements on the equipment purchased this time. After the visit, the customer was very satisfied with the equipment of our company. He said that he had seen our mature and advanced technology and strong production strength during the visit, and decided to cooperate with our company. On the same day, the customer signed a cooperation contract with our company. Good quality and intimate service is the most powerful marketing, thanks to the customer's