The finished product of blister packing machine Appearance of the finished package: The blister should be full, smooth and clean; The batch number in the plate should be clearly identified and the position should be accurate, and there should be no pollution of the plate phenomenon; PVC and aluminum foil sealing place should be tight, smooth, clear pattern, no wrinkling, pressure wear phenomenon; PVC and aluminum foil at the corner of the plate shall not be separated; No burrs at the edges and corners of plates. Dimensions of finished package: The size difference of the plate length and the plate width is ±0.3mm. The sealing distance between the blisters is not less than 2.5mm, and the sealing distance between the edge of the blister and the edge of the plate and the tear line is not less than 2.5mm. Sealtightness of finished package: Plate sealing is tight, no liquid infiltration blister or sealing layer. Filling rate of finished package: There shall be no lack

Operation requirements of blister packing machine The connection of each part of the packing machine should be firm and reliable, and the air control, air passage and water passage system should be smooth, and there should be no leakage. During the operation of the packaging machine, each moving part should be coordinated, flexible, accurate and in place, and the movement state switch of the moving mechanism should be flexible and reliable, without dead point, hard magnetic impact, stuck phenomenon. There should be no abnormal noise during no-load operation of the packaging machine, and the noise pressure level should not be greater than 82dB (A). The packing machine should be equipped with batch numbering device, the structure is easy to disassemble and assemble. The tear line of the packaged product should be kept intact without penetration, consistent in depth, and easy to be torn by hand.

Blister packing machine price and benefit analysis (1) Technical performance, including production speed, finished product quantity, quality, yield, consumption of raw materials, power, degree of automation, safety, impact on environmental protection. (2) Applicability, whether the complete supporting system of the whole machine is complete, whether the interface device with extended function is reserved, whether it has the same technical performance for multiple varieties and specifications, whether it is convenient to operate and change the mold in use, what are the requirements for the applicable environmental conditions, and the degree of adaptation to raw materials. (3) the reliability of equipment is prone to failure in the process of work, whether at work requires constant adjustment, whether to remain unchanged for a long time continuously, the technical performance of the machine operator level in the power, voltage, environment changes in the conditions, whether the

The appearance requirements of blister packing machine 1. The surface of exposed metal parts should be treated with anti-rust treatment. 2. The painted part of the outer surface of the machine should be beautiful and elegant, with harmonious tone, and the painted surface should not have obvious stripes and scratches. 3. All parts of the packaging machine should be neat in appearance, without burr and obvious scratches, and the surface, corners and edges in contact with the packaging should be smooth, smooth, easy to clean and disinfect. Packing machine should be able to be packaged according to the characteristics of the material, with the corresponding feeding device to adapt to different packaging, structure should be easy to disassemble; The inner wall of the parts in contact with the medicine of the hopper (box) and the feeding device should be smooth, smooth and without dead Angle. 4. The feeding device is in the form of mixing, and the brush and stirring blade shall n

The packaging significance of blister packing machine Pharmaceutical blister packing machine is a packaging machine used to pack oral solid tablets. The heating, molding and many other operations of plastic sheets are often completed in the same medical blister packing machine. In order to enable people to better understand this kind of mechanical equipment, the advantages of this kind of system equipment are summarized as follows: 1. Blister packing has good barrier property. The good barrier of such equipment is mainly determined by the packaging of the raw materials themselves. By comparing with bottled drugs, it can be seen that the drug can effectively reduce the required pollution after blister packaging and is convenient for patients to carry the drug. At the same time, after blister packaging, tablets also have obvious advantages in phase gas barrier, moisture permeability and many other aspects. 2. Another advantage of such packaging is the safety of drug packaging. T

Safety matters of blister packing machine 1. It is strictly prohibited to start the machine when the working frequency of the machine exceeds 40 frequency. When the four plates are blanked, the blanking times shall not exceed 56 times/min. 2. Press the manual right traction every time you press "start" or "dot move" to prevent the moving clamp from being damaged in the boot position. 3. When wearing PVC and loosening up and down the mold, the time of "loosening" should not be too long. Loosening 1-2 cm is enough to prevent the machine from being damaged to the greatest extent. 4. It is strictly prohibited to add lubricating oil during start-up or operation. 5. The feeding frequency in operation can be adjusted by the vibration frequency. 6. In operation, it is forbidden to clean the waste at the punching outlet, between the heat sealing roller and the driving roller, at the mold place, and at the batch number printing place. 7. No hard objects shall fall into the u

Blister packing machine feeding adjustment Carefully check each mechanical part of the equipment is abnormal, according to the provisions of the clearance and cleaning equipment. Check the connection of power supply, water source, air source and pipelines; Clear the obstacles around the body and check the fastening of bolts. Fill the machine with suitable lubricating oil according to the ambient temperature. Put the material to be packed into the hopper. Remove the cone plate sleeve outside the PVC bearing shaft, load the PVC drum into the bearing shaft, install the cone plate sleeve, and tighten the cone sleeve moderately. Boot, in "manual mode", open the "heating, heating, heat sealing heating" function, inching devices, make PVC through preheating zone, forming die, loading area, test area, heat sealing mould, drawing gas holder, indentation die, blanking die, install the waste after cutting edge to waste collection agencies, to complete the installation of the PVC.

The function of blister packing machine The whole machine can be packed in separate parts to enter the 2.2m elevator and the segmented purification workshop. It is fixed by screws when it is combined and easy to assemble. The mould and guide rail are designed independently. Only the integral guide rail is needed to change the mould. The mould pressing plate is clamps, so it is very convenient to load and unload. The design of the suspended operation platform, the operator in the use of the process of safety and maintenance of the convenience of cleaning the machine, The modular design of the station structure realizes the digital display control during the adjustment of each station, which ADAPTS to the diversified demands of the indentation forms and ensures the clarity of the indentation and batch number. Equip with photoelectric compensation device, can carry out the printed aluminum foil picture and text matching. The main motor adopts frequency conversion speed regu

The parts of the aluminum-plastic blister packing machine In pharmaceutical production, aluminum-plastic blister packaging machine has a variety of forms, complete packaging operation method also has the difference, but their composition and its components have the same function, mainly from paper, heater, molding department, packing department, the department of heat sealing, pinch device, printing device, cutting department, transmission system, the body and air pressure, cooling and electric control, variable frequency speed regulation system. (1) Release section. Plastic film and aluminum foil coils are fixed on the equipment, which is equipped with pressing, braking and axial position adjustment devices, and some are also installed with cursor tracking devices. (2) Heater. The heater uses electric heating to soften the plastic film for molding. (3) molding part. It is composed of forming plate, connecting valve plate, vacuum compressed air system, cooling water system,

Points for attention of blister packing machine 1. Before starting the machine, all parts of the machine must be cleaned. Any tools and sundries must not be put on the machine, so as to avoid vibration down and damage the machine. 2. The handle must be removed before starting the production to avoid the handle being thrown out. 3. Before starting the machine, you must declare "starting the machine" to the relevant personnel around the machine. 4. Do not start the machine when the protective cover of each part is opened. 5. During the boot process, always pay attention to the direction of PVC aluminum foil to prevent deviation. 6. If any problem is found in the starting work, the power shall be cut off in time and the maintenance personnel of the power equipment department shall be informed. 7. If the machine failure or quality problem is found, it must stop the machine and deal with it, and all kinds of fault shall not be eliminated in the operation of the equipmen