Servo Drive application of blister Packaging machine Servo driver switches and applications Servo drive based on equipment operation order, a drive is A2 molding servo drive, the second is the blanking of A2 servo drive, the third is a molding B2 servo drive, the fourth is the active stick B2 servo drive, is the fifth type B2 servo drive, the sixth is the cutting knife B2 servo drives. Main encoder installed behind the forming of B2 servo driver, so in addition to forming servo drives, servo drives off the rest can run independently after forming mechanism, second, if turn off type servo can run independently and blanking forming and sealing, third, closed type servo driver can run independently in addition to the type of all locations. Servo driver manual setup and application In the actual tuning process, the servo driver will use three main functions: parameter setting, manual operation, and acceleration setting. One parameter setting includes the length of forming servo rec

Use of die for sheet pressing machine In tablet production, tablet press and die are the equipment to press granular preparation into tablets directly. As the main consumables in the pressing process, the dosage of the die is very large. During the stamping process, shanyu die is mainly subjected to the axial alternating load, and its axial force is generally 50-100kN, which has a great loss to the die. Proper and reasonable usage can guarantee the quality of the tablet and the service life of the mold, thus reducing the transportation cost. During the use of the mold, attention should be paid to: (1) Die room shall be set up in the press section, and special personnel shall be responsible for the checking, inspection, maintenance, storage and release of molds. (2) The roughness of the mold should be checked before and after use to check whether there are flanging, missing Angle, blasting and wear of the sheet. The surface of engraving die should be bright to prevent sticking, il

The manipulator problem of blister packing machine 1. Position adjustment of manipulator Manipulator CAM in blanking servo motor above, when the CAM operation to a very high point, blanking knife open space is larger, the position of the manipulator sucker should be placed in the state of plate, CAM position is very low, blanking knife press, suction plate. If the sucker position is not correct, the fish-eye bearing screw can be adjusted to achieve. 2. Problems and treatment of grasping plate of manipulator If the length of the grabber nozzle is too long, it will break the sealing aluminum foil, and if it is too short, it will not grasp firmly and produce the stripper, or even the stripper. This problem can be solved by adjusting the position of the nozzle rod. In the operation process of the equipment, the vibration and mechanical transmission will cause the loosening of the bolts and screws of the equipment, so it is necessary to do a monthly inspection, as well as lubrication

Press adjustment of double layer press machine A particle is added into a feeder press, and the weight difference of the test piece meets the requirements. The second kind of particle is added into the feeder press, and the weight difference of the measured pieces meets the requirements. If you choose two kinds of double-layer tablet press which can produce the tablets at the same time, it can meet the requirements at the same time. Two kinds of particles were added into two feeder to suppress the two-color tablets, and the weight difference of the tablets was detected to meet the requirements of internal control. Connect the dust suction tank and powder suction nozzle. Observe the effect of dust (powder) to ensure that the particles of the two materials can not be mixed, before the formal tablet. After normal tablet pressing, each index of tablet is tested at specified intervals. After several batches of tablets, the gap between the feeder and the middle die plane of the turntable

Blister packaging machine plate table problem Splicing is PVC docking station, at the same time, splicing machine has two cylinder controlled release of PVC and outage protection, when forming servo traction, clamping cylinder to loosen, when forming traction to pulling the end of the clip clamping cylinder PVC, PVC continue to prevent: pick up table with another cylinder is open when powered on, turn it off when closed, to prevent the PVC stick for a long time in the heating plate and the scorched, splicing stage and the third function is to adjust the position of the PVC when asymmetric PVC waste edge on both sides can adjust splicing machine block when bar to control the center of the PVC. Splicing machine location prone to two problems, one question, after each sheet PVC in molding servo easily when wandering or fine, appear this kind of problem because of docking PVC edge is not neat, or butt paste transparent tape is not smooth, or is a splicing of retaining clip PVC is too t

Feeder for double layer sheet press The feeders of two kinds of materials of double layer tablet press should ensure that they cannot flow into each other. This requires special design improvements. A layer of material feeder is the same as the ordinary grid feeder. In order to prevent the upper punch from taking the material out, a layer of transparent cover plate shall be added to the feeder. The material is fed out quantitatively by the filling rail along the circular arc of the turntable and then returns to a layer of material feeder. The second layer of material feeder is designed as a box, which seals the material flowing from the special feeding box above, and the filling rail quantitative overflow material is also in the box. This kind of feeder is simple in structure, and the output of pressing sheet cannot be maximized. The two layers of material feeder are in the form of ordinary grid feeder, and a transparent cover plate is added on the feeder, but the material that is

The problem of blister packaging machine blanking The equipment provides universal disk brush blanker and disk vibration track blanker. The disk blanker is simple to use and has no big problems basically. If the blanking is too much or too little, it may be because the sensitivity of the blanking proximity sensor is not accurate. The sensitivity of the sensor can be adjusted. If the blanking rate is not high, the speed of the plate brush can be changed. Disc feeder accurate adjustment place more so, the first installation disc feeder disk to keep parallel with equipment platform, second, after forming blister alignment cutting board, platform and blanking plate is perpendicular to the equipment, and higher than 2 mm to 3 mm, the third through the alignment of the blanking plate to adjust the disc hole and blanking plate leakage hole alignment, then tighten the disc vibrator and disc. Multiple grains or skipping grains appear in blanking. This kind of circumstance is blanking plate

The work of double layer tablet press The main work of the double-layer tablet press includes the first layer of material filling, quantifying and prepressing, and the second layer of material filling, quantifying, main pressing, stripping and other procedures. Driven by the turntable, the upper and lower punching dies move clockwise along the upper and lower rail guide respectively. When the punch moves to the filling section of the first layer, the upper punch moves upward to bypass a layer of material feeder. At the same time. Down by the downward rail cant move down, at this point, the upper surface of the punch and die forming a cavity, powder materials after feeder concone fill the mould cavity, the punch through down the downward track low form excessive filling (pack), tablet press punch with the turntable continue movement, down after filling the rail gradually upward movement. The excess powder particles in the inner hole of the medium mold are pushed out into the quantita

Blister packaging machine molding prone to problems Forming air leakage, high noise, first forming leveling, inching control screen, when the molding upper mold at the low point to stop, and then the lower mold fitting on the mold, and keep all sides equal to further pre-tightening, later adjustment in the pre-tightening process should not only maintain no air leakage or less air leakage, but also ensure that the molding noise is not too big. Shape encoder parameters adjustment, inching, when the upper and lower mold just fitting immediately stop, you can try several times, find a suitable point. There are encoder synchronization values in the upper right corner of the control screen. Molding adjustment, point, when the mould and lower mould has 0.5 mm clearance stop or be asked in the mold put a layer of PVC, then the mould joint on the mould, and then through the PVC plate, heat, running at a speed of 25 to 35 cut/min, which Angle is the bolt tightening the Angle of leak unt

Dust-collecting device of double layer tablet press The dust suction device of common monochrome tablet press generally adopts single or double layer powder suction nozzle, and the dust generated during the pressing is inhaled by the dust suction machine. Suppression of double-layer tablets either feeder feeding way, by scraping powder plate out of the overflow particle can guarantee the uniformity of filling, but the tiny dust will also exist in turntable model plane, especially in the mold on the plane and die in the turntable on plane between 0. 01, 0. 05 mm clearance of fine dust, equipment running can cause mixed color phenomenon for a long time, only the first layer material after preloading, two layers of material master pressure molding position behind the increase in special vacuum cleaner, the fine dust in the plane of the die in turntable by suction machine suction, to ensure long-term continuous operation. In order to improve the recovery rate of double piece of materia