Pressure adjustment of the tablet press First, open the main switch, and then press the pressure (decompression) button, pressure, decompression repeatedly, the residual air out of the tube. Punch pressure is adjusted according to material nature and punch diameter. For the material with large blade diameter, low viscosity and not easy to form, the larger blade impact pressure can be obtained by programming. Plate diameter, high viscosity, easy to form, stamping strength is small. When adjusting the filling volume, the left hand steering wheel controls the weight of the workpiece pressed by the left hand pressure wheel. When the steering wheel rotates clockwise, the filling volume increases, that is, the filling depth increases. When the steering wheel rotates counterclockwise, the filling amount decreases, that is, the filling depth decreases. The central adjustable steering wheel controls the weight of the parts pressed by the direct press wheel. When the adjustable handwhee

Other factors affecting the capsule filling machine Other factors affecting the capsule filling machine generally include environment and transportation. The environment A fully enclosed environment is mainly reflected in temperature and humidity. The ideal relative humidity condition is 35-65%, and the temperature is 15-25℃. Too low humidity will make the shell brittle and easy to decompose. A capsule with high humidity will become sticky and deformed. Too high a temperature will cause thermal damage to the capsule. The transportation In the process of transportation, if the hollow capsule is impacted, the deformation of the capsule may hinder the filling of the capsule in the production process, affecting the production efficiency and product quality. To ensure the quality of the capsule products, the first to ensure that the production conditions meet the requirements, reasonable transportation. Now, with the continuous improvement of filling technology, the degree of automati

Liquid blister packaging machine Liquid filling machine Flat aluminum foam packing machine suitable for honey, jam, cheese, salad sauce, tomato sauce, chocolate sauce, perfume, essence, facial mask, condom, lotion, face cream and other aluminum foam packing. The machine is compact in structure, beautiful in appearance, stable in operation and simple in operation. It adopts internal heating to make PVC material heated evenly, and the blister is formed firmly. It is an advanced blister packaging machine in China. Automatic traction of the machine air clip, through the photoelectric eye detection position, the signal is transmitted to the pneumatic valve, control the air clip automatic start stop, walk equal distance. Automatic feeding and waste collection of the machine, through the photoelectric eye and servo motor, to achieve automatic feeding and DPP-170 and DPP-170 or more models of automatic waste collection. Automatic production count, through the detection of automatic

The operation skill of the tablet press 1. Before use, all containers, oil holes and friction surfaces of the press should be filled with lubricating oil. When running without load, oil film should be applied to all friction surfaces to extend the service life of the machine. 2. Before starting the electric compressor, several tablets must be manually tested before and after each shift to ensure the service life of the mold. 3. Storage die: After cleaning, apply a layer of food grade lubricant, put it into a special protective box or die storage box, and put it on the shelf. 4. Filter the material before pressing to prevent the material from producing flake, flake and flake weight difference during pressing. 5. Select the mold type: The correct selection of the mold type is the first step to successful stamping. For example, chewable tablets must be very hard and easy to chew; Because thin film coating is required, a slightly concave shape can be chosen. Due to the absen

The working process of the capsule filling machine Capsule filling machine is intermittent movement, the hole disc automatic capsule filling machine is completely closed in the filling and rotating parts, easy to clean, the upper and lower modules one-way movement into, imported polyurethane sealing lip, clean blowing induction module combined, to ensure that there is no dust, high-speed locking device is equipped with dust collection device. The hopper of the capsule filling machine is inserted into the hollow capsule to seed the tube. There is a switch under the seeding tube. While the seeding of the pipe is geared under the department's leadership, a touch switch is placed under the action of the iron to release the capsule. Has been under the capsule to comb the capsule by function forward to push board, compression of capsules capsule head pushed down and back, empty air suction capsule, comb downward pressure compression, capsule by air suction mould, because there is a sma

Pre-work procedure of blister packaging machine 1. According to the safety electricity standard, turn on the power for lighting. When the test is completed, turn on the power to ensure access to the ground wire and start the main motor. 2. Water connection: The cooling water enters according to the signal board on the fuselage seat. Whether the outlet leaks or not shall be subject to the patency of water inlet and outlet. 3. Air pump: Connect the air compressor pipe to the air plug and open the air compressor at the same time. Air pressure can only be used if the pressure is greater than 0, 6-0,8mpa. 4. Refueling: Add oil to the box and transmission. The amount of refueling is about two thirds of the box capacity. 5.PVC plastic feeding shaft: Adjust the inner and outer taper nuts to make the mold run to the feeding point. After the PVC plastic passes through, the material support will be opened and pressed. Please note that the PVC plastic on the surface of the sheet is

Rotary press punch installation Before the punch is installed, the hopper, feeder and feeder stand must be removed and the turntable and rotary mounted punch should be cleaned, bit by bit, and prepared according to the installation steps. The fixing of screws outside the frame of the middle die the main steel frame is flat with the outer circle to prevent the punch from colliding too tightly with the screw fixing plate and frame. It should be placed flat with the middle die beating rod gently hammered in. The floor plan of the opening should not be higher than the floor plan of the turntable, should meet the conditions, and then tighten the screws. Up-stroke device: The tongue plate is inserted on the opening gap of the guide rail, the middle rod is greased, some oil is added in the running toolbar, one by one, tighten the rod with thumb and forefinger, check the flexible rotation of the upper and lower mold, no scratch problem can occur, the tongue plate must be removed after

The operating point of the capsule filler When the capsule filling works normally for a long time, direct contact with drugs should be adjusted, and when the drug batch is changed or interrupted for a long time, it should also be cleaned. A proper amount of lubricating oil/grease shall always be provided to the driving mechanism under the working surface of the machine tool to reduce wear of moving parts. Check the oil content of the main transmission once a month, supplement it in time when it is insufficient, and change the lubricating oil every half a year. As a rule of thumb, you should use oil. Clutch is the traditional overload safety protection, the clutch should not slip, but due to long-term use may appear slip phenomenon, when the clutch slip phenomenon, may have to tighten the nut to ensure the normal operation of the machine, for the purpose of protection. In the filling process of hard capsules, the vacuum separator of the vacuum system mainly sucks the caps

The fault of blister packing machine and its solution PVC material enters blanking card machine Reason: The external tangent of the feed roller is inconsistent with the center line of blanking guide plate, the frequency of the feed roller and blanking is inconsistent, and the material is blocked on one side after deviating into blanking. Solution: Adjust the blanking position, adjust the blanking frequency, and adjust the aluminum foil and PVC materials to be consistent. After blanking, the bubble cap plate is out of alignment Reason: left and right side out of line blanking and feeding roller work center position is not consistent, up and down out of line, feeding roller and blanking Angle is not consistent. Solution: Adjust the position of feed roller. Plate margin is not flush after punching Reason: groove wheel gap is large, the cutting edge is not uniform wear. Solution: Adjust the brake position and replace blanking.

Adjustment of tablet press These tablets have different dose requirements. The maximum dose is adjusted by the die diameter of the handle, and the minimum dose is adjusted by the hole depth of the intermediate die. The dosage of a drug shall be determined in accordance with the provisions of the prescription and the pharmacopoeia and may not be changed. Pressure is also required during the stamping process, which will also affect the actual thickness and appearance of the sheet. Pressure regulation is essential in stamping process. This is achieved by adjusting the flow rate in the die hole. Adjustment of filling depth (adjustment of tablet weight) Loosen the butterfly screw and loosen the gear plate. Turn the bottom set gear to the left so that the bottom impact lever rises, reducing the filling depth (reducing the weight of the pill). After adjustment, press down the tooth plate and tighten the butterfly screw. Pressure adjustment (sheet hardness adjustment) Tighten