Performance advantages of blister packing machine 1.The machine integrates mechanical, electrical and gas, completes more than 10 packing processes, all the procedures are controlled by computer, according to user requirements can be added photoelectric detection, waste removal devices, the whole machine is fully closed, in line with GMP standards. 2. The large plate of the frame body and the external exposed parts are all made of high-quality stainless steel plate, which is corrosion-resistant and meets the requirements of GMP standard. 3. High production efficiency, high blanking times, obviously higher than the domestic similar medicine machine. 4. This machine stepless frequency conversion speed regulation, speed regulation range is large, transmission noise is low. 5. This machine can be used with general feeding machine, turn feeding machine, disk feeding machine, wide range of packaging. 6. The mold is easy to change and the adjustment method is simple. The mold and guide

Introduction to the operation of blister packing machine Operation of plate type blister packing machine (1) Prepare medicines and packaging materials, replace the batch number template, install PVC and aluminum foil, check the cooling water, and clean the equipment carefully; (2) Turn on the power supply and switch on the compressed air; (3) Press the heating key, and respectively heat and heat sealing temperature control table to the appropriate temperature; (4) Pull the PVC sheet through the channel to the punching knife, and pull the aluminum foil to the heat sealing plate; (5) When the heating plate and the heat sealing plate rise to the appropriate temperature, adjust the cooling thermometer to the appropriate temperature; (6) When the drugs are covered with the whole feeding track, press the green button of the motor, open the empty car to run. After blowing, heat sealing and punching meet the requirements, press the pill bucket vibration button and the planet cloth switc

Configuration of blister packing machine 1, molding, heat sealing, batch number, indentation, blanking and other devices all adopt the rack-made mandlet positioning, shake the handle, all kinds of devices can easily move on the heart shaft, the machine is equipped with a ruler, convenient correction, rapid and accurate positioning. 2, manipulator traction, the use of double pendulum rod device, increase the adjustable range of traction stroke, can adapt to the packaging of various sizes of drug version. The machine to plate heating, positive pressure molding, upper and lower mesh, cylinder heat sealing, automatic feeding, automatic indentation, batch number, automatic blanking plate, simple operation and reliable operation. 3, the positive pressure air molding with the configuration of mechanical punch, to ensure that the bubble cap forming uniform crisp, suitable for large size or special shape of the packing of pills, medical equipment; Equipped with special automatic feeder, it c

Packing advantages of blister packing machine The blistering packaging of drugs is to fill the groove with tablets, pills, capsules and other solid drugs after the transparent plastic hard sheet is blistered, and then heat the aluminum foil coated with adhesive to bond together, forming an independent sealing package. Blister packaging has great advantages: firstly, it provides the patients with a single dose of medicine packaging, which is convenient and economical; Secondly, blistor packaging has the advantages of good performance, high production efficiency, low cost, small storage space, light weight and convenient transportation. Moreover, the safety is good, because the blister packaging can be printed with text, the hair and the drug can avoid the wrong drug phenomenon. Pharmaceutical blister packaging on the market at present is mainly PVC base material, PVC base material is made from PVC resin add certain processing AIDS, produced by the method of extrusion, rolling processi

Application of servo in blister packing machine (1) PLC pulse function is not strong. In many large or medium-sized PLC in order to improve the PLC operation speed, the high speed pulse output function modularization. There is often no high-speed pulse output on THE PLC CPU module. The servo has intelligent function, which can drive the motor without external pulse. (2) During the operation of the equipment, there is a period of high speed pulse output by PLC due to the start of some interference sources, which makes the servo in the original system appear wrong action. Interference is a headache in a live environment. In the design of the system, the intermediate links should be reduced as far as possible, and the motor motion curve should be realized by using the programming function in the driver, so as to reduce the interference caused by external pulse in the transmission process. (3) In order to make the positioning of the equipment more accurate, it is necessary to make

Material requirements of blister packing machine The packaging of medicine must meet the requirements of moistureproof, mildew proof, frost proof, heat proof and light proof. Metal aluminum non-toxic tasteless, has excellent shading sex, moisture resistance, resistance capability and taste, perfect foil to completely cut off any gas and light, can be the most effective protection by packaging, almost all the requirements not pervious to light and high barrier material, adopt aluminum foil as the barrier layer, so the aluminum foil is widely used in medicine packing industry, It is often used as an inner packaging material in direct contact with the drug. At present, compared with imported products, there is still a gap in the quality of aluminum foil application in China, mainly manifested in the following aspects: One is the number of pinholes in the medical aluminum box can not reach the use requirements. The number of pinholes in aluminum foil is a penetration defect, which seriou

Blister packing machine heating plate station problem (1) the forming of the PVC into bent, appear this kind of situation is often in the sealing station bubble, this problem occurs because the heating plate and the forming die is not parallel, uneven heating, causing big deformation of the heated to form a bent, appear this kind of circumstance needs to forming dies as a benchmark to leveling up and down heating plate; (2) The forming PVC bubble holes in the inner and outer sides of the mold are always not full. This phenomenon may be caused by gaps in the heating plate and instability in the temperature of the heating plate! Therefore, there is no gap in the heating period during the operation of the heating plate. (3) The air bubbles in the middle of the mold are not full, because the PVC is flexible after heating, and the PVC that is not held up in the operation process is naturally sagging under the influence of gravity. The middle PVC may be stuck on the cooling mold, leading

Unpacking matters of blister packing machine 1. When unpacking, check whether the machine is complete, whether the attachment is consistent with the list, and whether there is any damage during transportation. 2. The machine should be placed horizontally in the room without installing screws on the bottom foot. The rubber plate with a thickness of about 12mm should be placed on the bottom of the bottom foot to avoid damage to the ground and displacement. 3. open the mechanism to carry out a comprehensive cleaning, with a soft cloth slightly soapy water (or detergent) to wipe the surface oil, dirt, and then dry with a soft cloth. 4. For the sake of safe production, it should be connected to the ground wire according to the designated position of the ground plate. 5. The machine should be operated and maintained by full-time personnel. 6. the operator must be familiar with the operation manual, the machine structure, the use of basic understanding of the operation. 7. All kinds of

Blister packing machine packaging requirements China's laws have made more and more strict restrictions on product packaging, and put forward higher requirements on packaging labeling and printing. In the industry standard of pharmaceutical blister packaging machine, the packaging machine must have a batch number device. Packing machine printing generally adopts punch molding method to print out the production date and batch number. Batch number can be made in separate station, can also be with heat sealing, indentation in the same station. Indentation A piece of aluminum-plastic packaging medicine may be suitable for multiple use, for ease of use, can be pressed on a piece of easily cracked broken marks, the piece can be easily broken into a number of small pieces by hand, each small piece for a single dose. Blanking will be sealed after the ribbon packaging finished products blanking into the specified size (that is, the size of a piece) known as the blanking process. In order to

Operation procedure of bubble cap machine 1. The green indicator light is on, and the two heating switches, upper and lower forming and hot sealing, open the operation position respectively. The temperature controller controls the forming temperature, which is generally preset at 100℃C, and the second temperature controller controls the heat seal. The temperature is preset at 130℃C~140℃C. Upper and lower forming and heat sealing temperature controller preset temperature; Subject to specific discretion. 2. Put down the pressing block on the primer roller, and the temperature of the forming heating plate is in place, then open the host machine. Plastic PVC is formed first, and the forming bubble eye is in line with the hole position of the heat sealing mold. Observation of plastic (refers to the machine board surface has become a new PVC) walking whether the left and right deviation. If there is a bias should adjust the starting pressure roller seat to adjust the direction of the l